Development of a test method for a realistic, single parameter-dependent analysis of piston ring versus cylinder liner contacts with a rotational tribometer

Biberger, Julian; Füßer, Hans-Jürgen

doi:10.1016/j.triboint.2016.10.043

Cited by 29 publications

(18 citation statements)

References 36 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…They involve in their experimental study carbon nanotubes (CNTs) lubricant and lubricant additive, they report that the friction coefficient lessens as CNT augment. The study in [9] was further extended by B. Zabala et al. [11].…”

Section: Introductionmentioning

confidence: 93%

“…It is well known that the contact cylinder liner - piston ring susceptible to friction and wear, mostly related to ring load and temperature, work period and sliding speed, nevertheless it is very hard to expect the physical effect of this parameter with realistic values, for this reason, Julian Biberger et al. [9] used rotational tribometer with a novel testing method to perform friction and wear at a different level of pressure combustion chamber, ring temperatures and sliding speeds, they observed that for a small load, friction declines intensely when increasing sliding speed and wear rises for lesser temperature, whereas it decreases with greater temperature. Enhancing the surface conditions with the fine finish and surface treatment together with tighter tolerances implementation are essential to ensure better lubrication conditions, less friction, low wear and consequently good sealing effect between the cylinder wall and piston rings that leads to high engine efficiency, and longer service life span [13, 14].…”

Section: Introductionmentioning

confidence: 99%

“…[11]. They carried out an experimental and a simulation investigation for wear of piston ring and cylinder liner depending on another parameter than that declared by [9]. Theses parameters are surface coatings and finishing, lubrication starvation and oil type.…”

Section: Introductionmentioning

confidence: 99%

See 2 more Smart Citations

Effect of cylinder-liner rotation on wear rate: An experimental study

Musmar

Al-Rousan

Tlili

2019

Heliyon

View full text Add to dashboard Cite

In rotating cylinder-piston system, the largest losses source is frictional losses, accounting for 50% of the total frictional losses, thus it is important to optimize. Effect of incremental rotation of a cylinder liner on its wear rate was investigated. The engine speed, load and the cylinder rotating angle were the main parameter. The results showed that the wear rate may be reduced to the half simply by rotating cylinder liner every six hours’ time interval of working. The test was carried out in pairs using a piston cylinder with movable liner and compared to a standard cylinder liner (fixed liner). Angles of 60 o , 120 o , 180 o , 240 o , and 300 o were used for incremental movement. The same operating conditions for two cylinders were maintained for the purpose of comparison. Beneficial effects of reducing the wear rate for all components of the piston-cylinder arrangement associated with incremental rotational movement of a cylinder linear were noticed. A decrease in wear rate was obvious in the cylinder liner in rotation angles of 120 o and 240 o and it is almost one-fourth of the wear that occurs in the stationary cylinder liner.

show abstract

Section: Introductionmentioning

confidence: 93%

Section: Introductionmentioning

confidence: 99%

See 1 more Smart Citation

Effect of cylinder-liner rotation on wear rate: An experimental study

Musmar

Al-Rousan

Tlili

2019

Heliyon

View full text Add to dashboard Cite

show abstract

“…Beside a close-to-application specimen production, details of the test rig and the test procedure can be crucial for the correct transfer of the application results. For example Biberger et al implement a lubrication system with a very low flow rate for their ring/liner model tester, to match the deficient lubrication situation of the top piston ring [18]. The heating of the piston group with combustion gases is simulated by Johansson et al with a heat gun combined with a water cooling system for the liner [3].…”

Section: Introductionmentioning

confidence: 99%

Development of a Model Test System for a Piston Ring/Cylinder Liner-Contact with Focus on Near-to-Application Seizure Behaviour

et al. 2019

View full text Add to dashboard Cite

Physical simulations of tribo contacts in internal combustion engines can act as a supporting tool to match upcoming guidelines and emission restrictions. In particular, the scuffing resistance of the contact between the piston ring and cylinder liner suffers under decreasing oil viscosity and limitation of antiwear additives. This paper aims to provide an experimental method to simulate the scuffing of the piston ring/cylinder liner-contact and to validate this method with real engine parts and the literature from engine tests. The experimental methodology uses a linear tribometer TE77 to test specimens from original piston rings and liners under reciprocating motion. Additionally, the ring specimen is given the opportunity to perform secondary movements (ring twisting, ring turning) and to run under deficient lubrication conditions similar to the engine. A specially designed test strategy enables the reproducible creation of seizure of the tribosystem. The seizure resistance of two engine oils, tested for validation, correlates with the known engine performance. Therefore, the model test system can be seen as a reproducible tool for simulating seizure of a ring/liner-system, showing similar trends and wear mechanisms as in an engine. Surface analysis depicts similarities between the scuffed surfaces of an engine and the model and discusses the origin of seizure based on the model specimens together with the relevant literature.

show abstract

“…here are three main elements when optimizing the performance of Internal Combustion (IC) engines in terms of improved energy efficiency [1]. First, it is important to reduce the thermal loss, which accounts for 50-60% of all losses.…”

Section: Introductionmentioning

confidence: 99%

Impact Analysis of Oversize Cylinder Liner on Piston Ring and Surging for Main Engine

Tjahjono¹,

Andromeda²,

Tazani³

2019

Proceedings of the 11th Asia Pacific Transportation and the Environment Conference (APTE 2018)

View full text Add to dashboard Cite

Cylindrical liner is the place of burning to generate power or effort inside the Mother Machine. The size of the oversized diameter will affect the incomplete combustion. The purpose of this study was to determine the causes of broken piston rings and surging, the impact of oversized liners and strategies to minimize the impact of oversized cylinder liners. The research method used is SWOT analysis and questionnaire method distributed to 51 samples of students officer of ATT II class and on board interview. Oversized cylinder liner causes the piston ring to be broken and incomplete combustion causing surging turbocharger. Strategies to minimize the impact of oversized liner by replacing piston rings and cylinder liner, cleaning scavenging of water thrunk and piston groove for normal rinse air pressure and combustion quality increases

show abstract

Development of a test method for a realistic, single parameter-dependent analysis of piston ring versus cylinder liner contacts with a rotational tribometer

Cited by 29 publications

References 36 publications

Effect of cylinder-liner rotation on wear rate: An experimental study

Effect of cylinder-liner rotation on wear rate: An experimental study

Development of a Model Test System for a Piston Ring/Cylinder Liner-Contact with Focus on Near-to-Application Seizure Behaviour

Impact Analysis of Oversize Cylinder Liner on Piston Ring and Surging for Main Engine

Contact Info

Product

Resources

About