Design, Modelling, and Analysis of Novel Solar PV System using MATLAB

Banik, Ayan; Shrivastava, Anurag; Potdar, Ravindra Manohar; Jain, Sanjiv; Nagpure, Santosh Gopal; Soni, Mukesh

doi:10.1016/j.matpr.2021.06.226

Cited by 33 publications

(7 citation statements)

References 23 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Therefore, many countries (both developed and developing) are planning to transition to renewable energy technologies in order to meet the electricity demand of the growing population and improve utility grid operation [5][6][7][8][9]. Among all renewable energy technologies, the solar PV technology is the most widely used for a number of reasons [10]. The output power of a PV system is generally influenced by operating conditions, including environmental conditions and the occurrence of faults [11].…”

Section: Introductionmentioning

confidence: 99%

Optimization of Standalone Photovoltaic Drip Irrigation System: A Simulation Study

et al. 2022

View full text Add to dashboard Cite

This paper presents the optimal design of a photovoltaic (PV) drip irrigation system. Designing a PV system is based on calculated motor power, solar irradiance level and other meteorological parameters at a certain geographical location. Therefore, a simulation study of the designed PV system were performed by a PVGIS simulation tool. The PVGIS simulation tool analyzes the potential of power generation with optimal PV modules tilt angle and orientation on a monthly and annual basis, and an analysis of the overall shading situation (horizon) as well as the internal shading between the PV module rows. The selection of water pump and motor depends upon the depth of water table and desired discharge and head to operate the irrigation system. Furthermore, a locally developed Solar-Drip Simulation Tool (SoSiT) was used for load and supply optimization. Based on ambient temperature, solar irradiation and water requirements, SoSiT calculates net generation by a PV system and resultant water output of the irrigation system. The particular drip irrigation site has two zones; the maximum water requirement for zone 1 (row crop) is 50,918.40 Liters/day and for zone 2 (orchards) is 56,908.80 L/day. From PVGIS simulation results, the maximum daily energy production of the designed PV system was 6.48 kWh and monthly energy production was 201 kWh in the month of May. SoSiT results showed that the PV system fulfilled the required crop requirement by only using 28% of the potential water supply, and 72% of the potential water supply from a solar-powered pump was not used. This value is high, and it is recommended to grow more or different crops to utilize the fuel-free electricity from the PV system. The unit cost of PV-powered drip irrigation is USD 0.1013/kWh, which is 4.74% and 66.26% lower than the cost of subsidized electricity and diesel, respectively.

show abstract

Section: Introductionmentioning

confidence: 99%

Optimization of Standalone Photovoltaic Drip Irrigation System: A Simulation Study

et al. 2022

View full text Add to dashboard Cite

show abstract

“…The simulation model of DCSM is implemented by using Math Lab program [43][44][45][46], this type of traditional controllers has advantages using to improve the work and performance of operation for machines to get better results, especially in the field of control, so this paper proposes two models when DCSM operates at no load [47][48][49][50][51][52][53][54], the first model refers to speed control at constant value of speed while second model deals with variable speed at multi conditions. Fig.…”

Section: Simulation Model To Speed Control Of Dcsmmentioning

confidence: 99%

Simulation Model of PID Controller for DC Servo Motor at Variable and Constant Speed by Using MATLAB

Abdullah¹,

Shneen²,

Dakheel³

2023

Journal of Robotics and Control

View full text Add to dashboard Cite

The current simulation is conducted in order to develop an appropriate design for the control systems and control the speed of the electric motor. To obtain the appropriate and required design, work is carried out for two cases, a constant speed and the other case at variable speed in different conditions for operation of dc servo motor, these conditions include rotating in a clockwise direction, break and returns rotating in the opposite clockwise direction. Through the proposed working conditions, it is possible to obtain the best values for the parameters of the control unit that improve the working performance of dc servo motor, which were shown by the simulation results and their values were kp =5, ki=3 and kd=5 for PID controller. Which changed the system response speed, rise time and the upper and lower bypass ratio at acceptable rates and ratios to prove an improvement procedure in the work of the electric motor.

show abstract

“…SOLAR SYSTEM MODELING Basically, it is fundamental element of solar system. Direct current (DC) is generated when light falls on solar cell [24,25]. The relationship between solar irradiance and generated DC current is linear.…”

Section: System Modelmentioning

confidence: 99%

Modeling and Analysis of Voltage Source based Battery Energy Storage System in Microgrid to Improve Power Quality

Tariq

Mahmood

2021

PakJET

View full text Add to dashboard Cite

Rising demand of renewable energy sources based distributed generation poses several challenges in utility grid operation. These shortcomings have been solved by microgrid. Power quality improvement is the main technical challenge in the applications of microgrid. Renewable energy sources can be integrated with microgrid in a better way by introducing a battery energy storage system. Power quality improvement, voltage and frequency regulation and catering the intermittency of renewable energy sources are few advantages of battery energy storage system. Integration of voltage source-based battery energy storage system in solar photovoltaic connected microgrid is presented in this paper. Voltage level between main grid and generation of solar power is maintained with the help of battery energy storage system. Power quality improvement ofintegrated microgrid system is done with control strategy of bidirectional converter used in battery energy storage system. Hysteresis band current controller is used in this paper to control the currents of battery energy storage system. It is a simple as well as robust technique for reduction of total harmonic distortion and voltage profile improvement as shown in the simulation results. Total harmonic distortion of system voltage is reduced 0.20%. This paper also presents the power flow to the loads using hysteresis band current controller and without using hysteresis band current controller. It is also shown by results that 45kVA is the most feasible rating of VS to deal with both linear and non-linear loads. MATLAB/SIMULINK environment is used to model and simulate the overall system performance.

show abstract

Design, Modelling, and Analysis of Novel Solar PV System using MATLAB

Cited by 33 publications

References 23 publications

Optimization of Standalone Photovoltaic Drip Irrigation System: A Simulation Study

Optimization of Standalone Photovoltaic Drip Irrigation System: A Simulation Study

Simulation Model of PID Controller for DC Servo Motor at Variable and Constant Speed by Using MATLAB

Modeling and Analysis of Voltage Source based Battery Energy Storage System in Microgrid to Improve Power Quality

Contact Info

Product

Resources

About