Design and implementation of a room temperature control system: Microcontroller-based

Amoo, Abdullahi Lanre; Guda, H. A.; Sambo, H. A.; Soh, T. L. G.

doi:10.1109/scored.2014.7072989

Cited by 16 publications

(8 citation statements)

References 7 publications

(6 reference statements)

Supporting

Mentioning

Contrasting

Order By: Relevance

“…These systems are either one time programmable or need analog adjustment which is not accurate and more difficult to use. More recent, real time based temperature control using Arduino [17] was published. The system uses Arduino based on ATMEL 89C51, which is just one of the application of Arduino, hence, not original design work, more expensive, and time consuming as one is needed to first learn the Arduino IDE.…”

Section: Related Workmentioning

confidence: 99%

Design and simulation of an automatic room heater control system

Zungeru

Mangwala

Chuma

et al. 2018

Heliyon

View full text Add to dashboard Cite

This paper presents the design and simulation of an Automatic Room Heater Control system. This system allows the user to set a desired temperature which is then compared to the room temperature measured by a temperature sensor. With the help of a microcontroller, the system responds by turning ON any of the two (2) loads (Fan or a heater) automatically depending on the temperature difference. The Fan is triggered ON when the room temperature is higher than the set temperature and the heater is triggered ON when the room temperature is lower than the set temperature. The system was designed and simulated using Proteus 8, circuit building software used for building electronics system. Proteus software was used to design and simulate the main circuit, and Micro-C hex file was loaded on the Proteus schematic design. For coding the PIC Microcontroller, Micro-C compiler was used. A 5 V DC power supply was designed in order to provide a biasing voltage to most of the active devices used in the system design circuit. The DC power supply was designed and simulated using Multisim software. The system was simulated and simulation results were in accordance to the design specifications.

show abstract

Section: Related Workmentioning

confidence: 99%

Design and simulation of an automatic room heater control system

Zungeru

Mangwala

Chuma

et al. 2018

Heliyon

View full text Add to dashboard Cite

show abstract

“…As illustrated in block diagram there are mainly 3 sensors used namely MAX30100 (a sensor based on the principle of photoplethysmography [4] for determining the heart rate and oxygen level) [9], LM35 (a temperature sensor for detecting the body temperature) and LM393 (a moisture sensor for monitoring the presence of any wetness around the baby) [10]. Arduino Uno microcontroller receives inputs from the sensors.…”

Section: Methodsmentioning

confidence: 99%

Femone Health Monitoring System

Minoshma¹,

Jayamohan²,

Sharon³

2019

IJITEE

View full text Add to dashboard Cite

As per the medical reports, each year 4 million newborns die within 28 days of birth and more suffer from disabilities, diseases, infections, and injuries. According to 2017 death rate, about 8,02,000 neonatal deaths are reported in India. The inability to detect any discomforts/criticalness that the babies can go through in the initial stages of life can lead to permanent disabilities/disorders and even death. The absolutely imperative approach to shrunken the mortality rate is to detect neonatal criticalness and give timely attention. Enabling an environment for newborn safety depends on the availability of adequate health-care facilities, equipment’s, medicines and emergency care when needed. Femone Health Monitoring System is developed with an aim to detect the difficulties faced by the babies and make it available to the user as well as doctors for easy diagnosis and treatment. The proposed technique is a wireless noninvasive system which monitors the vital physiological parameters of neonates including heart rate, oxygen level, body temperature, and wetness. Heart rate, oxygen level and body temperature are measured using the principle of photoplethysmography (PPG). The measured parameters are sent to an MQTT server and are published through the Femone app in real-time. The system also records the neonatal conditions in a day to day manner for future reference. A number of clinical trials were conducted in order to check the performance and for validation.

show abstract

“…In [3] A.L. Amoo et.al have used an AT89C51 microcontroller which receives the ADC signal which is sensed by the temperature sensor LM35.…”

Section: Literature Reviewmentioning

confidence: 99%

Implementation of Automatic Temperature Control for Confined Area

Samath

Kamath

Nayak

et al. 2022

J. Phys.: Conf. Ser.

View full text Add to dashboard Cite

The main aim of this paper is to develop a low cost system which keeps the room temperature at a desired temperature throughout without any human intervention irrespective of any changes in the external environment. The heating system is switched on if the surrounding temperature is less than the desired temperature or the cooling system is switched as the temperature sensed by the sensor goes above the surrounding temperature. Nevertheless, these kind of systems still needs some kind of improvement for being a better alternative.

show abstract

Design and implementation of a room temperature control system: Microcontroller-based

Cited by 16 publications

References 7 publications

Design and simulation of an automatic room heater control system

Design and simulation of an automatic room heater control system

Femone Health Monitoring System

Implementation of Automatic Temperature Control for Confined Area

Contact Info

Product

Resources

About