Design a single band microstrip patch antenna at 60 GHz millimeter wave for 5G application

Saini, Jyoti; Agarwal, Sudhir

doi:10.1109/comptelix.2017.8003969

Cited by 79 publications

(35 citation statements)

References 7 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The Antenna is designed using fractal geometry which is widely used for wide band applications, and high beam width [16][17][18][19][20][21]. For the vehicular communication, this proposed antenna is very much suitable as high beam width is need for the application.…”

Section: Fractal Antenna Designmentioning

confidence: 99%

Fractal Antenna Design for Overtaking on Highways in 5G Vehicular Communication Ad-hoc Networks Environment

Rahim,

Mallik,

Sankar

2019

IJEAT

View full text Add to dashboard Cite

Vehicular Communication is designed for enhancing road safety and support autonomous driving becoming very popular in the present scenario. The proposed system aims to design a suitable and secured system for overtaking on highways. The main problem faced while driving vehicle on highways is to overtake a larger vehicle on narrow roads, where the driver visibility is limited and it is very risky to overtake from right side as there is a high probability of colliding with the vehicles coming in opposite direction. The proposed system solves the problem by establishing ad-hoc connection in 5G environment with the vehicle to be overtaken. The system consists of a communication unit designed with a controller along with various options which are used to decide when the vehicle can safely overtake. In this way the driver can safely overtake the larger vehicles without any risk of road accidents. The proposed system uses fractal geometry to design the antenna which is used for the vehicle to vehicle communication at 5G frequencies up to 20GHz

show abstract

Section: Fractal Antenna Designmentioning

confidence: 99%

Fractal Antenna Design for Overtaking on Highways in 5G Vehicular Communication Ad-hoc Networks Environment

Rahim,

Mallik,

Sankar

2019

IJEAT

View full text Add to dashboard Cite

show abstract

“…The top layer and bottom layer are consists of copper materials with a thickness of 17 m that give a good radiating performance. Meanwhile, the middle layer is formed by a Rogers RT5880 substrate that has a dielectric constant, εr of 2.2 and thickness of 0.254 mm [9][10][11], [21]. The performance of the microstrip antenna depends on its resonance frequency used and dimension.…”

Section: Antenna Designmentioning

confidence: 99%

Microstrip antenna design with partial ground at frequencies above 20 GHz for 5G telecommunication systems

Aziz

Seman

Chua

2019

IJEECS

View full text Add to dashboard Cite

This article presents the design of a microstrip patch antenna at different frequencies above 20 GHz that intended to be used for fifth generation (5G) telecommunication system. The design of microstrip patch antenna that has a radiating element with a rectangular shape and partial ground plane is proposed. The patch antenna is designed using a Rogers RT5880 substrate with dielectric constant, <em>ε<sub>r</sub></em> of 2.2. The results of the designed antenna design analyzed in terms of the reflection coefficient, bandwidth, gain, and directivity performance. The proposed patch antennas at design frequencies of 25.875 GHz, 38.75 GHz, 43 GHz, 46.25 GHz, 48.7 GHz, 51.5 GHz, 71 GHz, and 83.5 GHz have a fractional bandwidth, gain and directivity that respectively greater than 10.2 %, 2.159 dB and 2.562 dBi. All designs and analysis are performed by using the CST Microwave Studio software.

show abstract

“…The slots are loaded on the patch with different dimensions. The patch is delivered by the 50 ohm microstrip line feed and the antenna is simulated on a Rogers RT5880 dielectric substrate having relative permittivity of 2.2, loss tangent of 0.0009, and height of 1.6 mm [5], [9]. HFSS software is used for simulation purpose.…”

Section: Antenna Design Analysismentioning

confidence: 99%

“…The E slots have a length and width of 1.91 mm and 1.05 mm. The microstrip feed lines have a length and width of 0.4 mm and 3.25 mm [9]. The single band antenna has been designed at the work 59 GHz millimeter wave frequency.…”

Section: Antenna Design Analysismentioning

confidence: 99%

Design of a Single Band Microstrip Patch Antenna for 5G Applications

Chandana¹,

P.Deepthi²,

Teja³

et al. 2018

IJET

View full text Add to dashboard Cite

This article is about a single band microstrip patch antenna used for the 5G applications. And this antenna is suitable for the millimeter wave frequency. The patch antenna design consists of 2 E shaped slots and 1 H shaped slot. These slots are loaded on the radiating patch with the 50 ohms microstrip feed line. For the simulation purpose, Rogers's RT5880 dielectric substrate with relative permittivity of 2.2 and loss tangent of 0.0009 is used. The design and simulation of the antenna is done using HFSS (High Frequency Structure Simulator) software. The results are simulated for the parameters Return loss, VSWR, 3D Radiation pattern. The proposed antenna has a return loss of -42.4383 at 59 GHz millimeter wave frequency.

show abstract

Design a single band microstrip patch antenna at 60 GHz millimeter wave for 5G application

Cited by 79 publications

References 7 publications

Fractal Antenna Design for Overtaking on Highways in 5G Vehicular Communication Ad-hoc Networks Environment

Fractal Antenna Design for Overtaking on Highways in 5G Vehicular Communication Ad-hoc Networks Environment

Microstrip antenna design with partial ground at frequencies above 20 GHz for 5G telecommunication systems

Design of a Single Band Microstrip Patch Antenna for 5G Applications

Contact Info

Product

Resources

About