Cyclic hardening and fatigue behavior of stainless steel 304L

Colin, Julie; Fatemi, Ali; Taheri, Saïd

doi:10.1007/s10853-010-4881-x

Cited by 51 publications

(33 citation statements)

References 11 publications

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…Nonetheless, strong differences of fatigue life are found subsequently to these prestrains. Regarding strain controlled fatigue, prestraining is known to induce fatigue life reduction [7,47,48]. To explain this detrimental effect, three key factors are often highlighted:…”

Section: Discussionmentioning

confidence: 99%

“…Moreover, this difference of stress level, henceforth called "memory effect", is not the only parameter affected by a prestrain and modifications of other mechanical properties were also reported (e.g. cyclic stress-strain response and fatigue life [4][5][6][7][8][9][10][11][12][13][14][15], creep and ratcheting tendencies [14,[16][17][18][19][20] and fracture toughness [21]). Memory effect is thus of an overall importance for metallic materials.…”

Section: Introductionmentioning

confidence: 99%

See 1 more Smart Citation

Fatigue of OFHC pure copper and 316L stainless steel subjected to prior tensile and cyclic prestrains

Marnier

Keller

Taleb

2016

International Journal of Fatigue

View full text Add to dashboard Cite

Section: Discussionmentioning

confidence: 99%

Section: Introductionmentioning

confidence: 99%

Fatigue of OFHC pure copper and 316L stainless steel subjected to prior tensile and cyclic prestrains

Marnier

Keller

Taleb

2016

International Journal of Fatigue

View full text Add to dashboard Cite

“…Table 1 lists the description of the experimental fatigue data employed in this study. The data were gathered from EDF, its partners and the literature [11][12][13][14][15][16][17][18][19], which was obtained from standard specimens made of the 304L stainless steel as discussed in details in the corresponding references. It should be emphasized that all these tests are under constant amplitude fatigue loadings.…”

Section: Correlation Of Experimental Fatigue Data Using Equivalent Crmentioning

confidence: 99%

“…In this paper, S y is taken as 202 MPa [11] and k is taken as 0.15 [13] for the 304L stainless steel. For this criterion, the critical plane is defined as the plane of maximum shear stain amplitude.…”

Section: Fatemi-socie's Criterion [31]mentioning

confidence: 99%

Toward consistent fatigue crack initiation criteria for 304L austenitic stainless steel under multi-axial loads

Lei

Tran

Taheri

et al. 2015

International Journal of Fatigue

View full text Add to dashboard Cite

a b s t r a c tIn this paper, a new framework to correlate the experimental data of the 304L stainless steel under multiaxial fatigue loadings using a reference curve identified from the experimental data of standard uni-axial fatigue tests is proposed. A total of 15 available fatigue crack initiation criteria are tested on the experimental data of 225 fatigue tests collected from EDF (formerly known as Electricity of France), its partners and the literature. Based on the computational results, it appears that most of the crack initiation parameters of the 15 available criteria can be used to correlate the experimental fatigue data for the 304L stainless steel under uni-axial loadings. Under bi-axial loadings, most of these parameters appear not to be quite consistent. Two criteria are modified in order to better correlate the experimental fatigue data under bi-axial loads. A simple statistical approach to evaluate the consistency of the crack initiation criteria is also proposed. Based on the limited available experimental fagtigue data and within the new framework in this paper, the computational results show that the equivalent crack initiation parameters of the Varvani-Farahani's criterion, the modified Lagoda-Macha-Sakane's criterion and the modified Varvani-Farahani's criterion can be used to correlate the experimental fatigue data under both uni-axial and bi-axial loadings for the 304L stainless steel. These criteria may be used to predict the fatigue life of the material under different loading and testing conditions by using the experimental data from the standard uni-axial fatigue tests.

show abstract

“…This state, called the martensitic transformation, leads to hardening behavior during low-cycle fatigue. It is noted that the martensitic transformation depends on the amount of plastic deformation amplitude [5].…”

Section: Introductionmentioning

confidence: 99%

Effect of Cryogenic Temperature on Low-Cycle Fatigue Behavior of AISI 304L Welded Joint

Song

Kim

et al. 2018

Metals

View full text Add to dashboard Cite

Abstract:The aim of this study is to investigate the low-cycle fatigue (LCF) properties of an AISI 304L welded joint based on experimental data. The influential parameters on the LCF such as the specimen thickness, strain ratio and cryogenic temperature were considered in this experimental study. In order to investigate the thickness effect on the LCF behavior, two types of specimens with thicknesses of 5 mm and 10 mm were used in an LCF test. In addition, the fatigue tests were conducted under strain control with three different strain ratios of R = −1, 0, and 0.5 at room and cryogenic temperatures. Based on the results obtained by this experimental study, no significant effect involved with the thickness and the strain ratio were observed. However, it was clearly observed that LCF performance at room temperature is lower than that at cryogenic temperature. Finally, an LCF design curve that can be used in design of the liquefied natural gas (LNG) applications is suggested.

show abstract

Cyclic hardening and fatigue behavior of stainless steel 304L

Cited by 51 publications

References 11 publications

Fatigue of OFHC pure copper and 316L stainless steel subjected to prior tensile and cyclic prestrains

Fatigue of OFHC pure copper and 316L stainless steel subjected to prior tensile and cyclic prestrains

Toward consistent fatigue crack initiation criteria for 304L austenitic stainless steel under multi-axial loads

Effect of Cryogenic Temperature on Low-Cycle Fatigue Behavior of AISI 304L Welded Joint

Contact Info

Product

Resources

About