Corundum after-blow nozzles

Ignatova, T. S.; Rutman, D. S.; Yamov, V. N.; Permikina, N. M.; Min'kov, D. B.; Makarova, T. S.; Moiseev, V. F.; Konetskii, N. V.; Mukhin, A. A.; Karas, G. E.; Mil'shenko, R. S.; Privovarova, L. V.; Pozhivanov, A. M.; Nikokoshev, N. T.; Karpov, N. D.; Afonin, S. Z.

doi:10.1007/bf01285658

Refractories

1973

DOI: 10.1007/bf01285658

|View full text |Cite

Corundum after-blow nozzles

T. S. Ignatova

D. S. Rutman

V. N. Yamov

et al.

Help me understand this report

Search citation statements

Order By: Relevance

Paper Sections

Select...

Citation Types

Supporting

Mentioning

Contrasting

Year Published

1980

Publication Types

Select...

Article1

Relationship

Self Cite1

Independent0

Authors

Journals

Cited by 1 publication

(3 citation statements)

References 0 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The eutectic temperature of appearance of the liquid phase in this system (1380~ is less than the temperature at which the metal is poured into the ladle (1600-1650~C), and according to [35] the viscosity is high. Therefore, when a fresh portion of metal ispoured the contact crust is softened and is washed away under the pressure of the injected gas [27,36]. Thus we observe a kind of "chemical cleansing" of the tuyere from the reaction products.…”

mentioning

confidence: 97%

“…On the basis of investigations performed in conjunction with factories, the Eastern institute of Refractories has organized the manufacture of five types of tuyeres of corundum and periclase [27,38]. Table 4 lists the characteristics of artifacts manufactured by the Podolsk Refractory Artifact Works and by the Magnezit Combine.…”

mentioning

confidence: 99%

“…To r e i n f o r c e the g r a i n s of such powders and strengthen the structure, small amounts of finely d i s p e r s e d binder a r e incorporated into the m a t e r i a l [26][27][28][29]. E x p e r i m e n t a l data on the p r o p e r t i e s of specimens based on monofractional powders of electrocorundum, high-alumina chamotte of the 1 -0 .…”

mentioning

confidence: 99%

See 2 more Smart Citations

Refractory materials for purging metal with gases

1980

Self Cite

View full text Add to dashboard Cite

Recently, refining of steel outside the furnace, which permits a considerable reduction in the content of gases and nonmetallic inclusions in the metal and improvement of its quality, has attained wide use. Existing procedures for refining metal outside the furnace --vacuum treatment, treatment with synthetic slags, and purging with inert gases --differ from one another in complexity, cost of the equipment, and the technical efficiency.The advantages of purging metal with gases are the minimal capital costs and the possibility of using simple inexpensive equipment with the existing stock of steel-teeming ladles without significant reconstruction of the casting bays. Treatment of the metal with inert gases in the steel-teeming ladle also increases the output of the smelting units, reduces the consumption of electricity (by finishing the metal outside the furnace) and alloying additions (by transferring alloying to the steel-teeming ladle), and improves the quality of the metal by reducing its gas saturation and averaging the temperature and composition during its mixing --this is particularly important when the capacity of the units is increased.Purging of metal with inert gases in a steel-teeming ladle by means of devices with relatively large orifices (tubes, nozzles, etc. ) does not ensure preparation of a sufficiently developed gas/metal contact surface and reduces the refining efficiency; therefore, widespread use has been attained by the method of metal purging through gas-permeable refractories, laid in the bottom of the ladle [1][2][3][4][5][6][7][8][9][10][11][12]. Both outside [13][14][15][16] and in the USSR [17] the gas is fed downward to the steel-teeming ladle through a special refractory tuyere fixed into the ladle bottom (Fig. 1). The porous tuyere may be in the form of a truncated cone or pyramid with an internal porous sector, or two truncated cones with a common base.This article summarizes the experience gained in the development of refractory materials, used for metal purging, based on corundum, high-alumina chamotte, and periclase.The purging efficiency depends on the number and size of the gas bubbles and their distribution in the body of the metal, the purging time, the gas pressure, etc. Experience gained shows that with attainment of the required efficiency the gas consumption per ton of metal treated is 0.5-1 m a, corresponding, e.g., to a gas consumption of 50-100 m 3 at an excess pressure of 1 atm for 10 rain in a 100-ton ladle. An increase in the pressure of the purging gas (in comparison with the accepted excess pressure of 3-6 atm) may lead to jet effusion of the gas --this is undesirable [18]; the increase in the purging time is limited by the cooling of the metal [1].

show abstract

mentioning

confidence: 97%

mentioning

confidence: 99%

See 1 more Smart Citation

Refractory materials for purging metal with gases

1980

Self Cite

View full text Add to dashboard Cite

show abstract

scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.

Contact Info

hi@scite.ai

10624 S. Eastern Ave., Ste. A-614

Henderson, NV 89052, USA

Blog Terms and Conditions API Terms Privacy Policy Contact Cookie Preferences Do Not Sell or Share My Personal Information

Made with 💙 for researchers

Part of the Research Solutions Family.

Corundum after-blow nozzles

Cited by 1 publication

References 0 publications

Refractory materials for purging metal with gases

Refractory materials for purging metal with gases

Contact Info

Product

Resources

About