Correlation of structure and properties of melt spun PbSn30Sb7Cu quaternary alloys

El-Bediwi, Abu Bakr

doi:10.1002/crat.200410409

Cited by 6 publications

(6 citation statements)

References 9 publications

(7 reference statements)

Supporting

Mentioning

Contrasting

Order By: Relevance

“…It is therefore of interest to note that Sn-Sb-based alloys have recently emerged as serious candidate materials in the search for a lead-free solder to use in today's electronics industry [6][7][8]. Sn-Sb alloys furthermore have metallurgical uses, for instance as components in bearings [9], and have recently also been proposed as cathode materials for use in lithium ion batteries [10,11].…”

Section: Introductionmentioning

confidence: 99%

Old friends in a new light: “SnSb” revisited

Norén

Withers

Schmid

et al. 2006

Journal of Solid State Chemistry

View full text Add to dashboard Cite

Section: Introductionmentioning

confidence: 99%

Old friends in a new light: “SnSb” revisited

Norén

Withers

Schmid

et al. 2006

Journal of Solid State Chemistry

View full text Add to dashboard Cite

“…where L is the length of the vibrating part of the sample, d the density of the sample, K the radius of gyration of the cross-section about the axis perpendicular to the plane of vibration, and Z a constant depending on the resonance mode and assumes 1.875 for the fundamental mode (13).…”

Section: Methodsmentioning

confidence: 99%

Effect of irradiation and pre-ageing temperature on the mechanical properties of Al–Si alloy

El-Khalek

El‐Salam

2008

Radiation Effects and Defects in Solids

View full text Add to dashboard Cite

Al-1wt.%Si alloy samples in the solid solution state were irradiated with doses of gamma rays up to 1.75 MGy for 2 h in the temperature range from 423 to 553 K. Induced variations in structure, mechanical and electrical properties were traced by suitable techniques. Observed changes in the measured parameters, internal friction Q −1 , thermal diffusivity D th , dynamic elastic modulus Y and resistivity, ρ, were explained in terms of the role and mode of interaction of lattice defects in irradiated and thermally treated samples. Composition inhomogeneity and variations in mass distribution in the matrix were also considered. The structure identification of the samples was carried out by using conventional X-ray diffraction techniques and transmission electron microscopy micrographs.

show abstract

“…The tribological properties of tin-based bearing alloys with different compositions, (7% and 20%), have been investigated [1]. Structure, electrical resistivity and elastic modulus of SnSb7X (X = 0, Cu, Ag, or Cu and Ag) and Pb63-xSn30Sb7Cux [x=0 or x≤2.5] alloys have been studied and analyzed [2,3]. Electrical resistivity, elastic modulus and internal friction of Pb63Sn30Sb7 decreases after adding Cu.…”

Section: Introductionmentioning

confidence: 99%

Influence of Titanium Oxide on Creep Behavior, Microstructure and Physical Properties of Tin-Antimony and Tin-Aluminum-Antimony Based Bearing Alloys

Bediwi¹,

Grayb²,

Kamal³

2015

IJSEA

View full text Add to dashboard Cite

Influence of adding titanium oxide (TiO2) nanoparticles on creep behavior, structure, mechanical and thermal properties of tinantimony-lead and tin-aluminum-antimony bearing alloys have been studied and analyzed. Stress exponent of tin-antimony-lead and tinaluminum-antimony-lead alloys decreased after adding titanium oxide. Elastic modulus of tin-antimony-lead increased after adding titanium oxide. Internal fiction of tin-antimony-lead and tin-aluminum-antimony-lead alloys varied after adding titanium oxide. Microstructure of tinantimony-lead and tin-aluminum-antimony-lead alloys changed after adding titanium oxide. Strengths of tin-antimony-lead and tin-aluminumantimony-lead alloys increased after adding titanium oxide. Thermal parameters of tin-antimony-lead and tin-aluminum-antimony-lead alloys varied after adding titanium oxide. The Sn97Sb51Pb1(TiO2)1 alloy has better bearing properties such as lowest internal friction, high elastic modulus and higher thermal diffusivity for industrial applications .

show abstract

Correlation of structure and properties of melt spun PbSn30Sb7Cu quaternary alloys

Cited by 6 publications

References 9 publications

Old friends in a new light: “SnSb” revisited

Old friends in a new light: “SnSb” revisited

Effect of irradiation and pre-ageing temperature on the mechanical properties of Al–Si alloy

Influence of Titanium Oxide on Creep Behavior, Microstructure and Physical Properties of Tin-Antimony and Tin-Aluminum-Antimony Based Bearing Alloys

Contact Info

Product

Resources

About