Conical Diamond Element Enables PDC Bit to Efficiently Drill Chert Interval at High ROP Replacing Turbine/Impregnated BHA

Abstract

Developing reserves in Kazakhstan's Chinarevskoe field frequently requires the operator to drill an 8.5-in. vertical hole section through extremely hard carbonates which contain high concentrations of problematic chert inclusions. The first significant chert layer is encountered at 3050-3110m, which has 10-50% chert content. Penetrating the chert interval with PDC bits has been challenging and in many cases impossible due to the cutters' inability to withstand high impact forces, which resulted in catastrophic cutter damage. The application of impregnated bits on high-speed turbines (1300-1400 RPM) led to significant improvement in run lengths and this BHA became the standard approach. 1 One impregnated bit could drill approximately 550m at 3.4m/hr. The hole section typically requires three bits to reach TD.However, the impregnated bit generated very small cuttings and high frictional heat altered chip appearance hampering lithology characterization and efforts to identify formation properties. Additionally, the centrifuge was unable to separate the extremely small cuttings from the drilling fluid, resulting in a gradual increase in mud weight over the interval creating the need for constant mud replacement.Tests with PDC were once again attempted, but when the bit encountered a high percentage chert interval, the bits were damaged and pulled in poor dull condition (7-6-CR). After repeated attempts with PDC, the operator realized wellbore verticality was compromised, which required correction run with impreg/turbine BHA with not optimum parameters leading to extra drilling time. The drilling team conceded the chert layers could not be drilled with a conventional PDC/motor BHA. The operator required PDC bit that could efficiently drill long intervals of carbonate formation at high ROP with a durable cutting structure that would remain intact when encountering the chert intervals.To develop a durable bit solution, engineers used an FEA-based modeling system to implement an innovative hybrid-type bit by strategically positioning multiple conical diamond elements (CDE) and conventional PDC cutters across the entire cutting structure from bit center to gauge. This new-style cutting structure leverages the CDE's aggressive shape and superior impact and wear resistance to create a high-efficiency plowing/shearing action that improves performance in difficult formations. The analysis indicated the new hybrid bit would improve performance and be capable of surviving shock and vibration while drilling the hard carbonate/chert formations.The CDE bit was field tested on rotary steerable BHA and drilled 615m at an ROP of 9.1m/hr through the carbonate formation that contained 10-40% chert inclusions throughout the entire interval. Compared to offsets drilled with an impreg/turbine BHA, the CDE bit drilled 12% more meters at 166% higher ROP while providing good wellbore quality and came out with excellent dull condition (1-1-CT). The bit generated much larger cuttings enabling wellsite geologists to readily identify lithology t...

Investigation of the Cross‐Cutting Polycrystalline Diamond Compact Bit Drilling Efficiency

“…It is a shared goal for researchers and manufacturers to achieve better synergy between cutter technology and bit structure. Numerous developments have appeared in the past few years [9][10][11][12]: Smith Company launched an axeridge-type bit that incorporates three rock damage mechanisms, including cutting, extrusion, and turning over, and, up to now, total drilled footage amounts to 60, 960 m. Shear Bits Company proposed a composite bit (PEXUS) that combines two structure units slicing and shearing to fracture and intrude the rock, increasing the penetration rate in hard strata. Baker Hughes Company proposed a cone-PDC hybrid bit that combines the advantages of cutter extrusion and PDC cutter shear failure.…”

Study on the acceleration of single‐cone PDC composite bit

“…Baker Hughes company has developed a new hybrid bit product by combining fixed PDC and unfixed cone 13–15 . Smith bits of Schlumberger has successively launched 360° rotary PDC bit 16,17 and conical diamond element bits 18–20 . Chen proposes a new technology of single‐cone bit, which is composed of fixed and unfixed, 21,22 with the structural innovation, new research on new drill bits and new tools will have new breakthroughs 23,24 .…”

“…[13][14][15] Smith bits of Schlumberger has successively launched 360 rotary PDC bit 16,17 and conical diamond element bits. [18][19][20] Chen proposes a new technology of singlecone bit, which is composed of fixed and unfixed, 21,22 with the structural innovation, new research on new drill bits and new tools will have new breakthroughs. 23,24 In order to overcome the shortcomings of the prior art (Figure 1), improve the wear resistance of the single cone bit and prolong the service life of the bit, based on an in-depth analysis of the structural characteristics and working principles of the single-cone bit, this paper adopts the design concept of the single-cone bit + PDC bit and the principle that the PDC cutting teeth work slowly and alternately on the cone, with the design concept of single cone PDC composite bit proposed (Figure 3).…”

Experimental research on torque characteristic and weight distribution of the polycrystalline diamond compact–roller hybrid bit

“…Recent years, drill bit researchers from all over the world have conducted a series of worthwhile studies on new bit structures and new drilling methods to overcome this difficulty. [3][4][5][6][7][8][9] Fortunately, in 2009, a hybrid bit, which combines the structural features and the working principles of fix-cutter polycrystalline diamond compact (PDC) bit and roller cone bit, was developed by one service company as one of the successful cases. [10][11][12][13] As far back as 1930, the American Floyd L. Scott and his staff had invented the first hybrid bit which combines a fishtail and a roller cone bit.…”