Computer Simulation of the Processes of Mixing in Multilayer Nitride Coatings with Nanometer Period

Sоbоl, O. V.; Meylekhov, A. A.; Postelnyk, А. А.

doi:10.1007/978-3-319-93587-4_16

Cited by 2 publications

(1 citation statement)

References 11 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Plasma processes have recently become the basis of modern surface hardening technologies [1,2]. Due to the strong disequilibrium of such processes, it is difficult to simulate them [3,4], therefore, to predict the properties obtained as a result of plasma technologies of materials, the method of structural engineering began to be used [5,6]. This is especially important for engineering materials, where surface properties in most cases determine their functional characteristics.…”

Section: Introductionmentioning

confidence: 99%

An experimental analysis of the influence of electrolyte compositions, current density and duration of the microarc oxidation process on the structuralphase state and properties of VT31 titanium alloy

Subbotinа

Sоbоl

Belozerov

et al. 2020

EEJET

View full text Add to dashboard Cite

It was determined that in an electrolyte containing 1.75 g/L KOH+1 g/L Na 2 SiO 3 +2 g/L NaAlO 2 , with an increase in current density from 15 A/dm 2 to 50 A/dm 2 , the phase composition of the coating changes. In the three-phase state (aluminum titanate, rutile, and amorphous-like phase), with increasing j, instead of an amorphous-like phase, a crystalline mullite phase appears. The hardness of the coating increases from 5400 MPa to 12500 MPa. It was found that, in combination with aluminum titanate, mullite is the basis for achieving high hardness in the coating. The formation of a ceramic micro-arc oxide coating on the surface of the VT3-1 titanium alloy makes it possible to reduce the dry friction coefficient by more than 5 times to f=0.09. The effect of electrolysis conditions during micro-arc oxidation of the VT3-1 alloy (titaniumbased) on the growth kinetics, surface morphology, phase-structural state, and physical and mechanical characteristics (hardness, coefficient of friction) of oxide coatings was studied. It was found that the process in the mode of micro-arc discharges is stably implemented on the VT3-1 alloy in an alkaline (KOH) electrolyte with additions of sodium aluminate (NaAlO 2) and liquid glass (Na 2 SiO 3). This makes it possible to obtain coatings up to 250 μm thick. In this case, a linear dependence of the coating thickness on the time of the MAO process is observed. The growth rate of the coating increases with increasing current density. The highest growth rate was 1.13 μm/min. It was revealed that in an electrolyte containing 1 g/L KOH+14 g/L NaAlO 2 with an increase in the duration of oxidation from 60 to 180 minutes, the relative content of the high-temperature phase, rutile, increases. In the coatings obtained in the electrolyte 1.75 g/L KOH+1 g/L Na 2 SiO 3 +2 g/L NaAlO 2 , with an increase in the duration of the MAO process, the relative content of the amorphous-like phase decreases and the content of the crystalline phase of mullite (3Al 2 O 3. 2SiO 2)

show abstract

Section: Introductionmentioning

confidence: 99%

An experimental analysis of the influence of electrolyte compositions, current density and duration of the microarc oxidation process on the structuralphase state and properties of VT31 titanium alloy

Subbotinа

Sоbоl

Belozerov

et al. 2020

EEJET

View full text Add to dashboard Cite

show abstract

Structural engineering of multi-period (TiMo)N/ZrN vacuum arc coatings

2020

Funct.Mater.

View full text Add to dashboard Cite

Computer Simulation of the Processes of Mixing in Multilayer Nitride Coatings with Nanometer Period

Cited by 2 publications

References 11 publications

An experimental analysis of the influence of electrolyte compositions, current density and duration of the microarc oxidation process on the structuralphase state and properties of VT31 titanium alloy

An experimental analysis of the influence of electrolyte compositions, current density and duration of the microarc oxidation process on the structuralphase state and properties of VT31 titanium alloy

Structural engineering of multi-period (TiMo)N/ZrN vacuum arc coatings

Contact Info

Product

Resources

About

Computer Simulation of the Processes of Mixing in Multilayer Nitride Coatings with Nanometer Period

Cited by 2 publications

References 11 publications

An experimental analysis of the influence of electrolyte compositions, current density and duration of the micro­arc oxidation process on the structural­phase state and properties of VT3­1 titanium alloy

An experimental analysis of the influence of electrolyte compositions, current density and duration of the micro­arc oxidation process on the structural­phase state and properties of VT3­1 titanium alloy

Structural engineering of multi-period (TiMo)N/ZrN vacuum arc coatings

Contact Info

Product

Resources

About

An experimental analysis of the influence of electrolyte compositions, current density and duration of the microarc oxidation process on the structuralphase state and properties of VT31 titanium alloy

An experimental analysis of the influence of electrolyte compositions, current density and duration of the microarc oxidation process on the structuralphase state and properties of VT31 titanium alloy