Comparison of SVPWM, SPWM and HCC control techniques in power control of PMSG used in wind turbine systems

Tınğ, Naim Süleyman; Yaşa, Yusuf; Aksoy, İsmail; Şahin, Yakup

doi:10.1109/optim.2015.7426976

Cited by 11 publications

(3 citation statements)

References 9 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The output voltage converters Vao, Vbo, and Vco take only two-level values between Vdc and zero. The different techniques of PWM waveforms for voltage source converters in wind turbines are mainly classified into PWM based on triangle comparison or by utilizing Space Vector (SVPWM), a commonly used modulation technique for power converters [16]. The primary goal of any modulation technique is to obtain a variable output with a high-level component and minimal harmonics.…”

Section: Pulse Width Modulation Pwm Control Strategymentioning

confidence: 99%

Modeling and Control Strategies for DFIG in Wind Turbines: A Comparative Analysis of SPWM, THIPWM, and SVPWM Techniques

Alwash,

Al-Thahab,

Alwash

2023

JESA

View full text Add to dashboard Cite

The paper presents a comprehensive study on modeling a doubly fed induction generator (DFIG) and explores various control strategies for pulse-width modulation (PWM) in back-to-back (B2B) converter techniques. A DFIG is characterized by a wound rotor and three slip-ring induction machines, with the stator winding directly connected to the power grid and the wound rotor interfaced with the grid through a 3-phase AC/DC/AC converter. Typically, the converter connected to the grid is referred to as the grid side converter (GSC), while the converter attached to the rotor's slip-ring circuit is termed the rotor side converter (RSC). This research delineates various PWM-based B2B converter methodologies applied to the DFIG within wind energy turbines, aiming to regulate the RSC for optimal power capture. The study employs MATLAB/SIMULINK for constructing a multi-phase voltage source converter two-level (VSC-2L) model, leveraging different PWM techniques including Sine-PWM, Sinusoidal-PWM with third harmonic injection (THIPWM), and space vector PWM (SVPWM). These techniques are assessed based on total harmonic distortion (THD) using fast Fourier transform (FFT) analysis. The findings indicate that SVPWM offers several advantages, such as ease of digital implementation, lower THD, reduced switching frequency losses, and more efficient utilization of the DC link voltage, thereby enhancing control strategy effectiveness.

show abstract

Section: Pulse Width Modulation Pwm Control Strategymentioning

confidence: 99%

Modeling and Control Strategies for DFIG in Wind Turbines: A Comparative Analysis of SPWM, THIPWM, and SVPWM Techniques

Alwash,

Al-Thahab,

Alwash

2023

JESA

View full text Add to dashboard Cite

show abstract

“…Literature [63] introduced the hysteresis controller to improve the LVRT performance of the DFIG system. Nevertheless, the hysteresis current controller suffers some drawbacks like high chattering [64], significant harmonics [65], and extended operating time [66].…”

Section: Hysteresis Control Approachmentioning

confidence: 99%

“…Software‐based LVRT techniques do not need any auxiliary device to ride through low voltage fault of the DFIG system. Therefore, software based LVRT techniques are used as an alternative to hardware‐based LVRT techniques in the literature [55–80] and are explained in the following paragraph of this paper.…”

Section: Lvrt Techniques For Dfig Systemmentioning

confidence: 99%

Low voltage and high voltage ride‐through technologies for doubly fed induction generator system: Comprehensive review and future trends

Din

Zhang

Zheng

et al. 2021

IET Renewable Power Gen

View full text Add to dashboard Cite

The advantages, such as the mature control method, less volume of the converter and generator, make the doubly fed induction generator system prevalent in the wind power industry. Nevertheless, the doubly fed induction generator is more susceptible to grid faults and disturbances. The instantaneous high voltage fault may occur due to the excessive local reactive power after the doubly fed induction generator system achieving low voltage ride through, and then the wind turbine might be disconnected again. Hence, not only the low voltage ride through but also high voltage ride through capability should be required for the doubly fed induction generator system to meet the grid code requirements. A comprehensive review of the state of the art low voltage ride through and high voltage ride through technologies for the doubly fed induction generator system is presented. Firstly, different types of common low voltage ride through and high voltage ride through techniques are classified according to their features, i.e. auxiliary hardware, linear or nonlinear control strategies etc. The pros and cons of different low voltage ride through and high voltage ride through techniques are given. Furthermore, the latest developments of low voltage ride through and high voltage ride through technologies are introduced. Finally, the future trends of both the low voltage ride through and high voltage ride through technologies are discussed. 1 INTRODUCTION Wind energy has become one of the most extensively disseminated new energy sources owing to the clean and efficient characteristics. The wind power industry has developed rapidly in China since the beginning of the 21st century. The installed capacity of grid-connected wind power will be expected to reach 210 GW by the end of 2020 [1]. Wind energy development and utilisation have started to develop in a decentralised manner, especially at the end of the power grid. Due to the long distance of the transmission line, the impedance of the power grid seen from the wind turbines increases, and the short circuit ratio (SCR) becomes small, which is the main characteristic of the weak grid. As the proportion of grid-connected wind power is increased and scattered into the weak grid, operational characteristics of the power grid, such as weak inertia, low SCR, This is an open access article under the terms of the Creative Commons Attribution License, which permits use, distribution and reproduction in any medium, provided the original work is properly cited.

show abstract

Wind Energy Conversion Systems: A Review on Aerodynamic, Electrical and Control Aspects, Recent Trends, Comparisons and Insights

Yousefzadeh,

Ahmadi Kamarposhti

2024

Green Energy and Technology

View full text Add to dashboard Cite

Comparison of SVPWM, SPWM and HCC control techniques in power control of PMSG used in wind turbine systems

Cited by 11 publications

References 9 publications

Modeling and Control Strategies for DFIG in Wind Turbines: A Comparative Analysis of SPWM, THIPWM, and SVPWM Techniques

Modeling and Control Strategies for DFIG in Wind Turbines: A Comparative Analysis of SPWM, THIPWM, and SVPWM Techniques

Low voltage and high voltage ride‐through technologies for doubly fed induction generator system: Comprehensive review and future trends

Wind Energy Conversion Systems: A Review on Aerodynamic, Electrical and Control Aspects, Recent Trends, Comparisons and Insights

Contact Info

Product

Resources

About