Compact Planar UWB Patch Antenna with Integrated Bandpass Filter &amp;#x0026; Band Notched Characteristics

Jangid, Shilpa; Kumar, Mithilesh

doi:10.1109/csnt.2012.12

Cited by 10 publications

(9 citation statements)

References 9 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…To include the impact of series resistance of inductors of CS-LNA for optimizing the noise figure are modified [9] and is given by Eq. (11).…”

Section: Common Source Topologymentioning

confidence: 95%

“…With reference to the above formulation of noise figure including the impact of series resistance (11) and noise figure of CG-LNA (5), the theoretical analysis of the proposed design is done without using the input-output matching network. Figure 3 shows the noise equivalent circuit of the two stages of CG with CS LNA.…”

Section: Noise Figure Optimization Using Cg-cg-cs Lnamentioning

confidence: 99%

“…A number of LNAs based on CMOS technology has also been reported earlier [7][8][9][10][11]. The 40 GHz three-stage cascaded TFMS tuned amplifier using 0.18 lm CMOS technology demonstrates a peak gain of 7 dB [7].…”

Section: Introductionmentioning

confidence: 97%

“…The integration of MURATA pass-band filter with patch antenna at 10 GHz achieved a return loss of 24 dB [10]. The compact planar ultra wideband patch antenna with integrated band-pass filter and band notched characteristics has been analyzed in [11].…”

Section: Introductionmentioning

confidence: 99%

See 3 more Smart Citations

A Miniaturization Approach Towards 40 GHz Integrated Single Chip Receiver System for MMW Communication Networks

Kumar

Kanaujia²,

Dwari

et al. 2015

Wireless Pers Commun

View full text Add to dashboard Cite

A full integration of single chip receiver system is remains to be a challenge in the area of millimetre wave (MMW) applications. In this paper, the integration of antenna, filter and CMOS low noise amplifier (LNA) is proposed which provides a new tri-design receiver system for MMW communication networks. A three-stage CMOS LNA is designed and integrated with co-design of filter and rectangular microstrip antenna which relaxes 50 X impedance matching constraint for designing at 40 GHz. Moreover, the new tri-design technique heavily improves the overall system integration, minimizes the noise and reduces the chip area and thus saving overall cost of the system. A three-stage CMOS LNA design is simulated and layouted using 90 nm CMOS design kit in ADS.v.12. The simulation result of CMOS LNA shows an achievement of 3.8 dB noise figure, 15.8 dB gain and -28 dB of return loss using proper impedance matching network. In addition, a theoretical analysis of three-stage CMOS LNA without using input-output matching network is done for the optimization of noise figure. A co-design of filter and patch antenna is also analyzed and integrated with CMOS LNA circuit. Finally, tri-design of receiver system demonstrates a peak gain of 25 dB and noise figure of 2.8 dB using proposed method.

show abstract

“…To include the impact of series resistance of inductors of CS-LNA for optimizing the noise figure are modified [9] and is given by Eq. (11).…”

Section: Common Source Topologymentioning

confidence: 95%

Section: Noise Figure Optimization Using Cg-cg-cs Lnamentioning

confidence: 99%

Section: Introductionmentioning

confidence: 97%

Section: Introductionmentioning

confidence: 99%

See 2 more Smart Citations

A Miniaturization Approach Towards 40 GHz Integrated Single Chip Receiver System for MMW Communication Networks

Kumar

Kanaujia²,

Dwari

et al. 2015

Wireless Pers Commun

View full text Add to dashboard Cite

show abstract

“…Antenna is one of the most important components in UWB systems. Ideally, the UWB antenna should be compact, planar and low cost [1].…”

Section: Introductionmentioning

confidence: 99%

Overview of UWB Low-Profile Planar Antennas

Schneider¹,

Gamec²

2014

AEI

View full text Add to dashboard Cite

Historical overview of evolution wideband antennas and some practical realizations of UWB antennas are presented. Practical realization of antennas are made by LTCC technology mostly, PCB technology or their combinations. Main features of antennas such as wide frequency bandwidth, high gain and the smallest dimensions as possible are described. The features should be helpful for future research of described antennas suitable for UWB radar applications.

show abstract

Multi-application Antenna for Indoor Distribution Antenna System like Wi-Fi, Wi-max and Bluetooth

Pal¹,

Kavitha²

2016

Proceedings of 2nd International Conference on Intelligent Computing and Applications

View full text Add to dashboard Cite

Compact Planar UWB Patch Antenna with Integrated Bandpass Filter & Band Notched Characteristics

Cited by 10 publications

References 9 publications

A Miniaturization Approach Towards 40 GHz Integrated Single Chip Receiver System for MMW Communication Networks

A Miniaturization Approach Towards 40 GHz Integrated Single Chip Receiver System for MMW Communication Networks

Overview of UWB Low-Profile Planar Antennas

Multi-application Antenna for Indoor Distribution Antenna System like Wi-Fi, Wi-max and Bluetooth

Contact Info

Product

Resources

About