Chemical Composition of Ceramic Tile Glazes

Ануфрик, С. С.; Kurian, N. N.; Zhukova, I. Yu.; Znosko, K. F.; Belkov, M. V.

doi:10.1007/s10812-016-0360-8

Cited by 5 publications

(3 citation statements)

References 1 publication

Supporting

Mentioning

Contrasting

Order By: Relevance

“…In their research, the absorption value of CTA is 2.4 times higher than the NFA due to the high porosity property of CTA (28.13% higher than NFA). Moreover, there is higher presence of micro-pores on the surface of the CTA than NFA which leads to an increase in the water absorption level of the specimen with replacement (Anufrik et al, 2016). The rising values of absorption in CHB with replacement in Figure 7 can be linked to the high porosity and micro-pores of CTA.…”

Section: Water Absorptionmentioning

confidence: 96%

Integrating Fine Ceramic Tile Aggregates in Concrete Hollow Blocks

Ramirez,

Remolisan,

Coscos

et al. 2023

IOP Conf. Ser.: Earth Environ. Sci.

View full text Add to dashboard Cite

This study investigates the effect of fine ceramic tile aggregates (CTA), specifically floor and wall tiles, as a replacement for fine aggregates in non-load bearing Concrete Hollow Block’s (CHB) fresh and hardened properties. The experimental design of this study performed was in line with the American Society of Testing and Materials (ASTM) standard procedure. Results for the workability of CHB with CTA showed comparable behavior to the control mix, which ranged between low to medium slump values (49 mm-59 mm). Specimens with CTA are characterized by higher water absorption and lesser density and moisture content. All the CHB with CTA replacement yielded higher compressive strength than the control mix. The 30% CTA substitution gained the highest compressive strength of 3.20 MPa (462.12 psi) for 28-days of curing. Overall, the physical and mechanical qualities of the samples with CTA percentage performed better than the control mix.

show abstract

Section: Water Absorptionmentioning

confidence: 96%

Integrating Fine Ceramic Tile Aggregates in Concrete Hollow Blocks

Ramirez,

Remolisan,

Coscos

et al. 2023

IOP Conf. Ser.: Earth Environ. Sci.

View full text Add to dashboard Cite

show abstract

“…Most of the simulation/modeling approaches to determine the relationship between raw materials and final properties consider the typical raw material and/or mineralogical ratios of body formulation and neglect the effect of chemical (oxide) content. However, the oxide content could have a significant effect on the final properties of ceramic tiles as indicated by [37][38][39][40][41].…”

Section: Introductionmentioning

confidence: 99%

Statistical analysis of porcelain tiles’ technical properties: full factorial design investigation on oxide ratios and temperature

Zamani,

Yapicioglu,

Kara

et al. 2023

Phys. Scr.

View full text Add to dashboard Cite

This study focuses on optimizing the composition and firing temperature of porcelain tiles using statistical analysis techniques. A full factorial design, including model adequacy checking, analysis of variance, Pareto charts, interaction plots, regression model, and response optimizer is employed. The key factors were the Seger ratios of SiO2/Al2O3, Na2O/K2O, MgO/CaO, and firing temperature. The response variables investigated were bulk density, water absorption, linear shrinkage, coefficient of thermal expansion (at 500 °C), and strength. The statistical analysis revealed highly significant results, which were further validated, confirming their reliability for practical use in the production of porcelain tiles. The study demonstrated the effectiveness of utilizing Seger formulas and properties of typical raw materials to accurately predict the final properties of ceramic tiles. By employing SiO2/Al2O3 = 5.2, Na2O/K2O = 1.50, MgO/CaO = 3.0, and firing temperature of 1180 °C, optimized properties, such as maximum strength, maximum bulk density, and minimum water absorption, was achieved with a composite desirability of 0.9821.

show abstract

“…A wide variety of the glazes are formulated depending on the type of product, firing temperature, and the desired effects and properties of the final product (Burleson, 2003). Recently, some studies investigated the application of design of the experiments to optimizing the glaze preparation (Ghosh, 1990;Ross, 1995;Roy, 2001;Anufrik et al, 2016). Since cost and time are two crucial parameters in industry, less cost in the least time is therefore desired.…”

Section: Introductionmentioning

confidence: 99%

Untitled

2017

J. Graph. Eng. Des.

View full text Add to dashboard Cite

The glaze, like the ceramic body, is made up of a series of inorganic raw materials. The main component of the glaze is silica glass as well as other elements that act as fluxes (alkalis, alkaline earths), former (boron, zinc, etc), opacities (zirconium, titanium, etc), and as coloring agents (chromium, cobalt, Manganese, etc). Although several glass-forming systems exist, ceramic glazes are almost completely based on alumina-silicate glass systems. The main glass forming oxide, silica (SiO 2 ) is modified by adding a range of other oxides. The modifiers act to alter thermal, chemical, and physical properties of the product, (Table 1) (Vari, 2000;Burleson, 2003).

show abstract

Chemical Composition of Ceramic Tile Glazes

Cited by 5 publications

References 1 publication

Integrating Fine Ceramic Tile Aggregates in Concrete Hollow Blocks

Integrating Fine Ceramic Tile Aggregates in Concrete Hollow Blocks

Statistical analysis of porcelain tiles’ technical properties: full factorial design investigation on oxide ratios and temperature

Untitled

Contact Info

Product

Resources

About