Calculation of Preliminary Bending of Strip During Cutting by Shears

Nikitin, G. S.; Епифанцев, А.; Демина, И.

doi:10.17073/0368-0797-2016-2-142-143

Izv. vysš. učebn. zaved., Čern. metall.

2016

DOI: 10.17073/0368-0797-2016-2-142-143

|View full text |Cite

Calculation of Preliminary Bending of Strip During Cutting by Shears

G. S. Nikitin¹,

А. Епифанцев²,

И. Демина³

Abstract: Аннотация. Разработана методика расчета расстояния от верхней поверхности ролика подводящего рольганга до верхней поверхности ролика отводящего рольганга устройства для резки предварительно изогнутой полосы исходя из условий минимизации усилия резания полосы при выполнении требования ее прямолинейности после реза.Ключевые слова: ножницы, резка, предварительно изогнутая полоса, допустимый прогиб, упругая деформация.

Help me understand this report

Search citation statements

Order By: Relevance

Paper Sections

Select...

Citation Types

Supporting

Mentioning

Contrasting

Year Published

2019

Publication Types

Select...

Article1

Relationship

Self Cite0

Independent1

Authors

Journals

Cited by 1 publication

References 1 publication

(1 reference statement)

Supporting

Mentioning

Contrasting

Order By: Relevance

Kinematics of Metallurgical Cutters With Parallel Blades

Bychkov¹,

Dvornikov²,

Жуков³

2019

Izv. vysš. učebn. zaved., Čern. metall.

View full text Add to dashboard Cite

Cutting with parallel blades cutters consists of three periods: blades ridging in metal; cutting; chipping (separation). Maximum force is required at the end of the ridging period and at the beginning of cutting. Since one of the blades is stationary, the second blade in cutting process has to go deep into the entire thickness of metal to cut the billet. For example, if thickness of metal is20 mm, then the upper blade needs to pass20 mmfor its cutting. If you make both blades moving towards each other, cutting eﬀort will be less. In this case, each blade cutting20 mmof metal will pass 10mm. In order not to make mechanism of cutter with two movable blades too complicated, it is important to ensure its mobility from one drive. So, there acute the issue of arrangement possibility of blades moving towards each other with guaranteed strength of the units, transmitting eﬀort on the blades. Kinematic scheme of cutters with blades moving parallel to each other in a vertical plane is proposed. Advantages of the proposed cutters design are the following: counter movement of blades requires less eﬀort to cut the billet; force from each blade is distributed to two connecting rods, reducing load on each of them; since blades move towards each other, the main cutting force is distributed along the units of the mechanism and is transmitted to the engine, which reduces load on the frame and foundation when cutting; when blades move towards each other, metal separation occurs faster, it allows to concentrate maximal force during cutting with minimal load on the engine; the cut part of the billet does not fall below the roller bed at the end of cutting, so installation of the lower movable table is not required. Mobility of the proposed mechanism is determined by P.L. Chebyshev formula with its value = 1. Kinematic analysis of blades is carried out using a special method, which is in using point of connecting rods intersection.

show abstract

Kinematics of Metallurgical Cutters With Parallel Blades

Bychkov¹,

Dvornikov²,

Жуков³

2019

Izv. vysš. učebn. zaved., Čern. metall.

View full text Add to dashboard Cite

show abstract

scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.

Contact Info

customersupport@researchsolutions.com

10624 S. Eastern Ave., Ste. A-614

Henderson, NV 89052, USA

Blog Terms and Conditions API Terms Privacy Policy Contact Cookie Preferences Do Not Sell or Share My Personal Information

Made with 💙 for researchers

Part of the Research Solutions Family.

Calculation of Preliminary Bending of Strip During Cutting by Shears

Cited by 1 publication

References 1 publication

Kinematics of Metallurgical Cutters With Parallel Blades

Kinematics of Metallurgical Cutters With Parallel Blades

Contact Info

Product

Resources

About