Ca-induced Plasticity in Magnesium Alloy: EBSD Measurements and VPSC Calculations

Chaudry, Umer Masood; Hamad, Kotiba; Kim, Jung-Gu

doi:10.3390/cryst10020067

Cited by 15 publications

(6 citation statements)

References 22 publications

(25 reference statements)

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Similar effects of precipitated (Mg,Al)2Ca particles in AZ31−0.5Ca alloy and G.P. zones in Mg-Al-Ca-Mn alloys on the reduced deformation anisotropy and enhanced plasticity of Mg alloys have been reported [49][50][51]. This study reveals that enhanced activity of non-basal slip is essential for the excellent plasticity of Mg alloys during deformation under a high-strain-rate condition.…”

Section: Microstructural Evolution Of Zk30 During Hot Compressionsupporting

confidence: 81%

Microstructural Study of a Mg–Zn–Zr Alloy Hot Compressed at a High Strain Rate

et al. 2020

View full text Add to dashboard Cite

Understanding the correlation of plasticity with deformation and dynamic recrystallization (DRX) behaviors, in magnesium (Mg) alloys deformed under high-strain-rate conditions, is increasingly important for wrought Mg processing. In the present study, a ZK30 (Mg-2.61%Zn-0.66%Zr by weight percent (wt.%)) alloy in the as-forged state was hot compressed to various strain levels at a temperature of 350 °C and a strain rate of 10 s−1. Heterogeneous deformation and dynamic recrystallization (DRX) behaviors of the complicated microstructures in the deformed samples were analyzed via a grain-partitioning approach based on intra-grain misorientation analysis from electron back-scattered diffraction (EBSD). The ZK30 alloy showed excellent formability, remaining intact at a true strain of −1.11. Continuous dynamic recrystallization (CDRX) and discontinuous dynamic recrystallization (DDRX) via grain boundary corrugation/bulging are the dominant mechanisms for the relaxation of strain energy during hot compression. Initial Zr-rich coarse grains undertook a significant portion of the plastic strain as the compression progressed, reflected by the increased misorientations within their interior and marked change in their aspect ratios. The results indicate that the excellent plasticity of the as-forged ZK30 alloy can be attributed to the operative CDRX mechanisms and the reduced deformation anisotropy of Zr-rich coarse grains containing Zn–Zr nano–precipitates.

show abstract

Section: Microstructural Evolution Of Zk30 During Hot Compressionsupporting

confidence: 81%

Microstructural Study of a Mg–Zn–Zr Alloy Hot Compressed at a High Strain Rate

et al. 2020

View full text Add to dashboard Cite

show abstract

“…The rolled plates are sampled for electron backscatter diffraction (EBSD) testing and room-temperature tensile tests. Then, the viscoplastic self-consistent model (VPSC) model is used to simulate the rolling deformation [ 18 , 19 , 20 , 21 ] of the above-mentioned representative ZK61 plate. Through the combination of symmetrical rolling and asymmetric rolling experiments, the aim is to prepare magnesium alloy sheets with high mechanical properties, and the yield strength, tensile strength and elongation of the final sheets are greatly improved.…”

Section: Introductionmentioning

confidence: 99%

Plastic Deformation Mechanism of High Strength and Toughness ZK61 Magnesium Alloy Plate by Multipass Horizontal Continuous Rolling

Chen

Liu

et al. 2023

Materials

View full text Add to dashboard Cite

ZK61 magnesium-alloy plate with high tensile strength and elongation is obtained by combined multipass symmetric hot rolling and asymmetric warm rolling. Deformation history considering varying strain rate obtained from the macro-finite element analysis of the selected passes are introduced into the viscoplastic self-consistent model (VPSC) as initial boundary conditions for macro- multiscale and micro-multiscale coupling analysis. VPSC simulation results show that in the initial stage of rolling deformation, the basal <a> slip is the dominated deformation mode, supplemented by prismatic <a> slip and pyramidal <c+a> slip. With increased rolling strain, the pyramidal <c+a> slip presents competitive relationship with basal <a> slip, and the activation amount of {10—11} compression twins is limited. During asymmetric rolling, the basal <a> slip is dominant, followed by the pyramidal <c+a> slip. Experimental results show that the basal texture is gradually strengthened after symmetric rolling, and grain size is refined due to the activation and recrystallization of twins. Asymmetric rolling makes the basal texture deflect 10° to the rolling direction and further refine the grain size. With the ongoing of symmetric rolling, the mechanical anisotropy of the plate weakens, and the yield strength, tensile strength, and plasticity of the material improves. In particular, after asymmetric rolling, the tensile strength in the RD and TD directions of the plate reaches 391.2 MPa and 398.9 MPa, whereas the elongation reaches 19.8% and 25.5%.

show abstract

“…Precipitation and solute segregation have also reported to be an efficient strategy to tweak the basal texture during recrystallization. Hence, common approaches being utilized are intelligent alloying, microstructure optimization and texture modification [14][15][16].…”

Section: Introductionmentioning

confidence: 99%

Investigating the Microstructure, Crystallographic Texture and Mechanical Behavior of Hot-Rolled Pure Mg and Mg-2Al-1Zn-1Ca Alloy

2022

Self Cite

View full text Add to dashboard Cite

In this study, the microstructure, crystallographic texture and the mechanical performance of hot-rolled pure Mg and Mg-2Al-1Zn-1Ca (herein inferred as AZX211) were thoroughly investigated. The results showed that the designed AZX211 alloy exhibited an exceptional strength/ductility synergy where an almost 40% increase in ductility was received for AZX211. The microstructural characterization revealed the grain refinement in the AZX211, where the grain size was reduced by more than 50% (24.5 µm, 10 µm for the pure Mg and the AZX211, respectively). Moreover, a discernible number of precipitates were dispersed in the AZX211, which were confirmed to be (Mg, Al)2Ca. The pure Mg showed a conventional strong basal texture while a significantly weakened split basal texture was received for the AZX211. The fraction of basal-oriented grains was 21% for the pure Mg and 5% for the AZX211. The significant texture weakening for the AZX211 can be attributed to the precipitation and co-segregation that triggered the preferential evolution of the non-basal grains while impeding the growth of the basal grains. This was also confirmed by the crystal orientation and the pseudo-rocking curves. The higher ductility of the AZX211 was explained based on the texture softening and Schmid factor for the basal and non-basal slip systems.

show abstract

Ca-induced Plasticity in Magnesium Alloy: EBSD Measurements and VPSC Calculations

Cited by 15 publications

References 22 publications

Microstructural Study of a Mg–Zn–Zr Alloy Hot Compressed at a High Strain Rate

Microstructural Study of a Mg–Zn–Zr Alloy Hot Compressed at a High Strain Rate

Plastic Deformation Mechanism of High Strength and Toughness ZK61 Magnesium Alloy Plate by Multipass Horizontal Continuous Rolling

Investigating the Microstructure, Crystallographic Texture and Mechanical Behavior of Hot-Rolled Pure Mg and Mg-2Al-1Zn-1Ca Alloy

Contact Info

Product

Resources

About