Back-side AlOx Passivation material and technology for the application of high efficiency (20%) and low cost PERC solar cells

Hung, Jui-Yi; Wang, Jung-ching; Chen, Shian-wen; Chen, Tsung-Cheng; Lin, Yung‐Sheng; Ku, Chen-Hao; Wen, Ching-Chang

doi:10.1109/pvsc.2014.6925642

Cited by 4 publications

(1 citation statement)

References 9 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Al 2 O 3 films deposited by all of these methods have been shown to be capable of providing excellent passivation in recent years. Various other deposition techniques, including sol-gel [92]- [94] and screen-printed pastes [95], [96], have also been investigated, though so far with less impressive results.…”

Section: Industrial Application Of Al 2 Omentioning

confidence: 99%

New Perspectives on Surface Passivation: Understanding the Si-Al2O3 Interface

Black

2016

Springer Theses

View full text Add to dashboard Cite

High-efficiency crystalline silicon solar cells must suppress recombination at their p-type surfaces. Thin-film, amorphous aluminium oxide (Al 2 O 3) has been shown to provide very effective passivation of such surfaces, assisted by its negative fixed charge. However, many details of Al 2 O 3 passivation remain poorly understood. Furthermore, conventional means of depositing passivating Al 2 O 3 are too slow or too expensive to be suitable for high-volume commercial production. This thesis addresses these issues in three ways: 1) by contributing to a deeper understanding of semiconductor-dielectric interfaces and semiconductor surface recombination mechanisms in general, 2) by investigating the properties of Al 2 O 3 as a passivating dielectric for silicon surfaces, and 3) by demonstrating the viability of APCVD as a high-throughput, industrially compatible deposition method for Al 2 O 3 , enabling its application to commercial solar cells. Using Al 2 O 3 as a test case, it is shown how a novel analysis of the extended conductance method can be used to i) distinguish the separate contributions to the interface state distribution at a semiconductor-dielectric interface, and ii) determine their capture cross-sections for both minority and majority carriers. Furthermore, the direct link between these measured interface state properties and the recombination rate at the semiconductor surface is experimentally demonstrated by showing that the former can be used to accurately predict the latter. Investigations of the surface passivation properties of Al 2 O 3 reveal a remarkably consistent picture. It is shown that the properties of the Si-Al 2 O 3 interface states are essentially independent of the Al 2 O 3 deposition conditions and technique. The interface properties are found to be independent of the surface dopant concentration at boron-and phosphorus-doped surfaces, while recombination is shown to be only weakly dependent on surface orientation and morphology as a result of the remarkable orientation-independence of the Si-Al 2 O 3 interface state properties. Meanwhile, the chemical origin of the charge at the Si-Al 2 O 3 interface is elucidated by correlating FTIR and electrical measurements. xi xii APCVD is clearly shown-for the first time-to be capable of depositing Al 2 O 3 films with exceptional surface passivation properties, comparable to the best results achieved using other deposition techniques. In the best case, interface state densities as low as 5 × 10 10 eV −1 cm −2 at midgap, and negative fixed charge concentrations of 3.3 × 10 12 cm −2 are measured, resulting in a saturation current density of 7 fA cm −2 on undiffused p-type surfaces. The APCVD films are shown to be thermally stable under standard solar cell processing conditions and are demonstrated in large-area solar cells with peak efficiencies of 21.3 %. These results demonstrate the viability of APCVD Al 2 O 3 as a surface passivation layer for industrial silicon solar cells.

show abstract

Section: Industrial Application Of Al 2 Omentioning

confidence: 99%