Autotransplantation With a 3-Dimensionally Printed Replica of the Donor Tooth Minimizes Extra-Alveolar Time and Intraoperative Fitting Attempts: A Multicenter Prospective Study of 100 Transplanted Teeth

Verweij, Jop P.; Westerveld, Kees J.H. van; Moin, David Anssari; Mensink, Gertjan; Merkesteyn, J.P.R. van

doi:10.1016/j.joms.2019.08.005

Cited by 22 publications

(33 citation statements)

References 58 publications

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…This conclusion is consistent with the results of previous studies on intentional replantation 25 . In most guidelines for autotransplantation, however, the tendency is to avoid an extra‐oral time exceeding 5 minutes 23,24 …”

Section: Discussionsupporting

confidence: 91%

“…During the surgical procedure, several parameters were checked. An intact PDL was a significant predictor ( P < .05) of further treatment success, emphasizing the importance of careful removal of the donor tooth and careful preparation of the recipient socket 11,23 . We found a significant relationship between the extra‐oral time of the transplanted tooth and treatment success ( P < .05).…”

Section: Discussionmentioning

confidence: 61%

“…These tools can allow for preparation of the recipient site beforehand with minimal extra‐alveolar time. Also, the use of a tooth replica may reduce the number of positioning trials in the recipient socket, thus preserving the viability of the PDL stem cells 11,23 …”

Section: Discussionmentioning

confidence: 99%

See 2 more Smart Citations

Survival and success of autotransplanted impacted maxillary canines during short‐term follow‐up: A prospective case‐control study

Grisar

Smeets

EzEldeen

et al. 2020

Orthod Craniofacial Res

View full text Add to dashboard Cite

Objectives This prospective clinical trial aimed to examine the predictability of maxillary canine transplantation as compared to biological canine eruption. Additional objectives were to examine hard and soft tissue outcomes, including aesthetic outcome compared to outcomes with the contralateral canines. Settings and Sample Population The sample comprised 17 consecutively transplanted maxillary canines in 17 patients (mean age at surgery, 18 years; range, 11‐29 years). Minimal follow‐up time was 12 months post‐transplantation. Clinical and radiographic parameters were recorded for the transplanted and contralateral canines, showing a natural eruption pattern. Material and Methods The Maxillary Canine Aesthetic Index (MCAI) and the Autotransplanted Maxillary Canine Radiological Index (AMCRI) were scored for all upper canines. Successful transplantation was considered as the absence of pathology during intermittent clinical and radiographic controls and a good‐to‐excellent outcome compared to the contralateral biological erupted canine, as defined by the MCAI and AMCRI. Results The mean follow‐up period was 28 months (±9; range, 12‐40 months). The overall survival rate was 100%, and the success rate reached 68% at 1 year post‐operatively. Significant predictors of success were the extra‐oral time during transplantation, amount of damage to the root surface, quality of surrounding tissues and immediate post‐operative oral hygiene. Conclusion Standardized measurements demonstrated clinically satisfactory outcomes with maxillary canine autotransplantation compared to outcomes with the contralateral canine during 1‐3 years of follow‐up. The potential predictors of success identified here should be confirmed with long‐term follow‐up studies.

show abstract

Section: Discussionsupporting

confidence: 91%

Section: Discussionmentioning

confidence: 61%

See 1 more Smart Citation

Survival and success of autotransplanted impacted maxillary canines during short‐term follow‐up: A prospective case‐control study

Grisar

Smeets

EzEldeen

et al. 2020

Orthod Craniofacial Res

View full text Add to dashboard Cite

show abstract

“…For all these reasons, orthodontic overcorrection is recommended to increase the space allocated to the recipient socket. Verweij et al [ 34 ] recommend performing the cone beam-computed tomography scan between 2 months and 2 weeks before the autotransplantation procedure, because the time taken to create a 3D replica of the donor tooth is approximately 2 weeks.…”

Section: Discussionmentioning

confidence: 99%

“…a.) Successful No signs of pathology NR less than 1 min 10 Kim et al [ 50 ] 2019 2 third molars Successful No signs of pathology NR 3 and 5 2–60 Xia et al [ 51 ] 2020 28 third molars Successful No signs of pathology SLA 1 to 5 Average: 2.5 24 Verweij et al [ 34 ] 2020 73 premolars 24 M - 3 others In 2016 98% Successful No signs of pathology DMLS 82% less than 1 min NR o. a. open apex, c. a. closed apex, NR Non-Registered, SLA Stereolithography Apparatus, Polyjet Material Jetting, SLM Selective Laser Melting, DMLS Direct Metal Laser Sintering …”

Section: Discussionmentioning

confidence: 99%

The use of 3D additive manufacturing technology in autogenous dental transplantation

et al. 2020

View full text Add to dashboard Cite

Background In medicine and dentistry, 3D technology allows the virtual planning and printing of surgical replicas of anatomical structures that can facilitate certain transplant procedures. In dentistry, 3D technology is useful in autogenous tooth transplantation. Case presentation We present a clinical case of an ectopic mandibular second premolar, describing the preoperative planning with dental replicas and the autotransplantation surgery. 3D prints of the surgical replica of the tooth to be transplanted was made using an Objet30 Prime® Printer, PolyJet. Clinical controls performed at 3, 6 and 12 months indicated the satisfactory evolution of the transplanted tooth. Conclusion 3D additive manufacturing technology allows the preparation of a new recipient socket with the aid of a surgical replica of the tooth to be transplanted, thus minimizing handling and extraoral time.

show abstract

Guided autotransplant of a first premolar to replace a maxillary ankylosed incisor using a custom-designed osteotome

Abella¹,

March²,

Zubizarreta-Macho³

et al. 2022

The Journal of the American Dental Association

View full text Add to dashboard Cite

Autotransplantation With a 3-Dimensionally Printed Replica of the Donor Tooth Minimizes Extra-Alveolar Time and Intraoperative Fitting Attempts: A Multicenter Prospective Study of 100 Transplanted Teeth

Cited by 22 publications

References 58 publications

Survival and success of autotransplanted impacted maxillary canines during short‐term follow‐up: A prospective case‐control study

Survival and success of autotransplanted impacted maxillary canines during short‐term follow‐up: A prospective case‐control study

The use of 3D additive manufacturing technology in autogenous dental transplantation

Guided autotransplant of a first premolar to replace a maxillary ankylosed incisor using a custom-designed osteotome

Contact Info

Product

Resources

About