Assessment of Settling Behavior of Particles with Different Shape Factors by LiMCA Data Analysis

Gökelma, Mertol; Brun, Pierre Le; Dang, Thien Ngon; Badowski, Mark; Morscheiser, Johannes; Friedrich, Bernd; Tewes, Sebastian

doi:10.1002/9781119274780.ch143

Cited by 4 publications

(2 citation statements)

References 1 publication

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Due to the difference in C D , the terminal velocity of a thin film will be different from an alumina particle although their density is identical. By an approximation of thin disc geometry, the terminal velocity of a thin film can be described as follows [16,34,35] :…”

Section: B Settling Behavior Of Oxide Films and Grain Refiner Particlesmentioning

confidence: 99%

The Interactions Between Oxide Film Inclusions and Inoculation Particles TiB2 in Aluminum Melt

Yang

Bao

Akhtar³

et al. 2021

Metall Mater Trans B

View full text Add to dashboard Cite

In this work, a systematic study on the interactions between aluminum oxide films and TiB2 grain refiner particles and their effect on grain refinement behavior have been conducted. Oxide films were introduced into a commercial purity aluminum melt by adding AA 6061 alloy chips while the grain refiner particles were introduced by adding Al-3T-1B master alloy. Strong sedimentation of TiB2 grain refiner particles was observed in aluminum melt without chip addition during long-time settling. Most of the TiB2 particles were settled and accumulated at the bottom of crucible. In contrast, the sedimentation of TiB2 particles is much less in the melt with the addition of oxide films. A large fraction of TiB2 particles were found to be adhered to the oxide films located at the top part of the crucible, which inhibited the sedimentation of grain refiner particles. TP-1 type tests were also done to study the grain refinement efficiency of Al-3Ti-1B master alloy under different melt cleanliness and settling time. It is found that sedimentation of TiB2 particles greatly reduces the grain refinement efficiency. The introduction of oxide films seems to slightly alleviate the fading effect. This is owing to the strong adherence between the oxide films and TiB2 particles, which leads to a retardation of particle sedimentation.

show abstract

Section: B Settling Behavior Of Oxide Films and Grain Refiner Particlesmentioning

confidence: 99%

The Interactions Between Oxide Film Inclusions and Inoculation Particles TiB2 in Aluminum Melt

Yang

Bao

Akhtar³

et al. 2021

Metall Mater Trans B

View full text Add to dashboard Cite

show abstract

“…This result brings the question if the detectable size also might be influenced by the shape of the particles. However, the shape factor has also a direct influence on settling velocity of particles which can cause different problems during the detection [31] [32]. The shape of the particles could have been a reason for unpromising results but more research is needed in this topic.…”

Section: Settling Effect On Detectable Particle Size Rangementioning

confidence: 99%

A Review on Prerequisites of a Set-Up for Particle Detection by Ultrasonic Waves in Aluminium Melts

Gökelma¹,

Latacz²,

Friedrich³

2016

OJMetal

Self Cite

View full text Add to dashboard Cite

In many applications in aluminium industry, the number of inclusion-critical products increases and the quality of those products depend on the inclusion concentration and size. In order to improve the quality of aluminium products and the effectiveness of the processes, a reliable and cheaper on-line detection method is needed. Ultrasonic detection has been used in steel industry, but relatively rare in aluminium industry, although it would theoretically allow for an online non-intrusive detection of the cleanliness of the melt. In this work, the current information on ultrasonic inclusion detection was gathered and recommendations were provided on the Prerequisites for a setup for ultrasonic detection of non-metallic inclusions in aluminium as a contribution on previous works. It has been concluded that ultrasonic waves seem promising, and should be experimented more on an industrial level to have a clear view on the potentials of the method.

show abstract

A PoDFA Benchmarking Study Between Manual and AI-supervised Machine Learning Methods to Evaluate Inclusions in Wrought and Foundry Aluminum Alloys

Gauthier,

Bilodeau,

Sosa

2024

The Minerals, Metals &Amp; Materials Series

View full text Add to dashboard Cite

Assessment of Settling Behavior of Particles with Different Shape Factors by LiMCA Data Analysis

Cited by 4 publications

References 1 publication

The Interactions Between Oxide Film Inclusions and Inoculation Particles TiB2 in Aluminum Melt

The Interactions Between Oxide Film Inclusions and Inoculation Particles TiB2 in Aluminum Melt

A Review on Prerequisites of a Set-Up for Particle Detection by Ultrasonic Waves in Aluminium Melts

A PoDFA Benchmarking Study Between Manual and AI-supervised Machine Learning Methods to Evaluate Inclusions in Wrought and Foundry Aluminum Alloys

Contact Info

Product

Resources

About