Applications of Porous Ceramics

Liu, P.S.; Chen, G.F.

doi:10.1016/b978-0-12-407788-1.00006-x

Cited by 49 publications

(76 citation statements)

References 23 publications

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…For physical properties analysis, the dimensional changes and the density were measured using Vernier caliper and densitometer that applies Archimedes principle respectively after sintering process. Porosity of the as-sintered parts was calculated based on direct method calculation using equation as follows (Liu and Chen, 2014):…”

Section: Characterization Of the As-sintered Partsmentioning

confidence: 99%

Development of Porous Ti-6Al-4V Mix with Palm Stearin Binder by Metal Injection Molding Technique

Jamaludin¹,

Kasim²,

Nor³

et al. 2015

American Journal of Applied Sciences

View full text Add to dashboard Cite

Good potential of biocompatibility and excellent mechanical properties, porous Ti-6Al-4V has become a great interest for biomedical applications. In this study, porous Ti-6Al-4V was fabricated by Metal Injection Molding (MIM) using Palm Stearin (PS) and Polyethylene (PE) binder together with sodium chloride (NaCl) as a space holder. Rheological characterization was performed to evaluate the flowability of the feedstocks for injection molding and the feedstocks exhibited a pseudoplastic behavior which is suitable for injection. The as-sintered parts were fabricated as the mixing, injection molding, debinding and sintering were conducted successfully. The mechanical properties of the as-sintered parts were investigated via tensile test and the results obtained were closed with the established range. Shrinkage, density and X-Ray Diffractometry (XRD) of the as-sintered parts were compared with the theoretical values which were found closed to the acceptable ranges. The microstructure of the surface and cross-section were observed under Scanning Electron Micrograph (SEM) and optical microscope to analyze the specimens before and after sintering. Generally, palm stearin binder system added with space holder to fabricate porous Ti-6Al-4V by MIM is feasible and has shown a good potential for biomedical applications.

show abstract

Section: Characterization Of the As-sintered Partsmentioning

confidence: 99%

Development of Porous Ti-6Al-4V Mix with Palm Stearin Binder by Metal Injection Molding Technique

Jamaludin¹,

Kasim²,

Nor³

et al. 2015

American Journal of Applied Sciences

View full text Add to dashboard Cite

show abstract

“…Наведені дослідження, які проводяться в напрямку отримання теплоефективної будівельної кераміки і окрес люють вектор розробок, вказують, що вони спрямовані на визначення впливу конкретних добавок на властивості матеріалів без системного аналізу найважливішого для поризованої кераміки взаємозв'язку «тип структури -властивість» [8]. В літературі бракує інформації стосовно технологічних способів регулювання пористої структури матеріалів для досягнення підвищеної конструктивної якості виробів.…”

Section: аналіз літературних даних та постановка проблемиunclassified

“…В Україні є практичний досвід використання тери конів в дорожному будівництві (будівництво кільцевої дороги в Донецьку) [8].…”

Section: вступunclassified

Process methods of pore structure and properties control of heat insulation ceramic construction materials

Щукіна¹,

Цовма²,

Галушка³

et al. 2015

TAPR

View full text Add to dashboard Cite

show abstract

“…Evidently, finding such description is a fundamental issue because it turns to be a necessary element for the general theory on the decay of multicomponent metastable liquid solutions [1,2]. As discussed previously, the formation of gas bubbles is widely applied in technological processes for the creationc of new porous materials and nano-and microcontainers [3,4]. The rapid, explosive growth of water vapor and accompanying dissolved gas bubbles in magmatic melt is one contributing mechanism for volcanic eruptions [5][6][7].…”

Section: Introductionmentioning

confidence: 99%

Evolution of size and composition of a multicomponent gas bubble in liquid solution

Kuchma¹,

Щекин²

2015

Nanosist.: fiz. him. mat.

View full text Add to dashboard Cite

The equations describing the transient and steady stages of size and composition evolution for a gas bubble which grows or shrinks due to the diffusion of several gases dissolved in liquid solution have been derived. The diffusion fluxes for gases in the liquid mixture caused by the bubble growth or dissolution were assumed to be quasistationary and the mixture of the gases in the bubble was treated as ideal. The analytical solutions for the obtained evolution equations have been found for bubbles of any size with an arbitrary number of components in the case of equal products of diffusivities and solubilities of dissolved gases in the liquid solution, and for sufficiently large binary bubbles for which capillary effects can be neglected.

show abstract

Applications of Porous Ceramics

Cited by 49 publications

References 23 publications

Development of Porous Ti-6Al-4V Mix with Palm Stearin Binder by Metal Injection Molding Technique

Development of Porous Ti-6Al-4V Mix with Palm Stearin Binder by Metal Injection Molding Technique

Process methods of pore structure and properties control of heat insulation ceramic construction materials

Evolution of size and composition of a multicomponent gas bubble in liquid solution

Contact Info

Product

Resources

About