Application of carbonated apatite coating on a Ti substrate by aqueous spray method

Mochizuki, Chihiro; Takano, Ichiro; Hayakawa, Tohru; Sato, Mitsunobu

doi:10.1016/j.msec.2012.11.027

Cited by 21 publications

(22 citation statements)

References 34 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The quality of coating adhesion measurements showed that the detachment of coating is less than 5% and could be classified between 5B and 4B according to ASTM standard. The results indicate that obtained CHA coatings have good adhesion strength [59]. …”

Section: Methodsmentioning

confidence: 78%

Synthesis and characterization of sol–gel derived calcium hydroxyapatite thin films spin-coated on silicon substrate

Malakauskaite-Petruleviciene

Stankevičiūtė

Niaura

et al. 2015

Ceramics International

View full text Add to dashboard Cite

Section: Methodsmentioning

confidence: 78%

Synthesis and characterization of sol–gel derived calcium hydroxyapatite thin films spin-coated on silicon substrate

Malakauskaite-Petruleviciene

Stankevičiūtė

Niaura

et al. 2015

Ceramics International

View full text Add to dashboard Cite

“…45 Self-cleaning was tested by dispensing oil droplets onto a surface followed by rinsing with high purity water. Oil-water separation efficiencies were measured by pouring a vigorously agitated mixture of oil and water over stainless steel mesh which has been dip coated with copolymer-fluorosurfactant complex.…”

Section: Introductionmentioning

confidence: 99%

Ultrafast Oleophobic–Hydrophilic Switching Surfaces for Antifogging, Self-Cleaning, and Oil–Water Separation

Brown

Atkinson

Badyal

2014

ACS Appl. Mater. Interfaces

148

122

View full text Add to dashboard Cite

. (2014) 'Ultra-fast oleophobic-hydrophilic switching surfaces for anti-fogging, self-cleaning, and oil-water separation.', ACS applied materials interfaces., 6 (10). pp. 7504-7511.Further information on publisher's website:http://dx.doi.org/10.1021/am500882yPublisher's copyright statement:This document is the Accepted Manuscript version of a Published Work that appeared in nal form in ACS Applied Materials Interfaces, copyright c American Chemical Society after peer review and technical editing by the publisher. To access the nal edited and published work see http://pubs.acs.org/doi/abs/10.1021/am500882y. Additional information:Use policyThe full-text may be used and/or reproduced, and given to third parties in any format or medium, without prior permission or charge, for personal research or study, educational, or not-for-pro t purposes provided that:• a full bibliographic reference is made to the original source • a link is made to the metadata record in DRO • the full-text is not changed in any way The full-text must not be sold in any format or medium without the formal permission of the copyright holders.Please consult the full DRO policy for further details. be further enhanced by the incorporation of surface roughness to an extent that it reaches a sufficiently high level (water contact angle <10° and hexadecane contact angle >110°) which, when combined with the inherent ultra-fast switching speed, yields oil-water mixture separation efficiencies exceeding 98%.

show abstract

“…The evaporation of solvent and deposition of fine and dry precursors make up the basic mechanism of the spray-deposition method [22,32]. In the case of molecular precursor solutions involving metal complexes, the accompanying elimination of ligands, ammonia in this case, plays an important role in forming amorphous precursor films of the desired compound, LCO, in the Li/Co ratio of 1.…”

Section: Fabrication Of Lco On Quartz Glass Substrate Via Spray-coatingmentioning

confidence: 99%

“…Aqueous precursor solutions were successfully developed in our recent studies [22,23], and these solutions can be easily applied for the fabrication of thin films via spray-coating under ambient conditions. The studies involved the fabrication of a carbonate-containing apatite film deposited on a Ti substrate and a highly conductive and well-adhered thin film of copper on a quartz glass substrate.…”

Section: Introductionmentioning

confidence: 99%

Thin Film Fabrication and Characterization of Layered Rock Salt LiCoO2 on Quartz Glass Spray-Coated with an Aqueous Ammonia Solution Involving Metal Acetates

et al. 2019

Self Cite

View full text Add to dashboard Cite

A LiCoO2 thin film on a quartz glass substrate was fabricated by a wet process involving heat treatment of a precursor film spray-coated with an aqueous ammonia solution containing LiCH3COO and Co(CH3COO)2. The precursor film formed onto the substrate at 180 °C in air, and was heat treated at 500 °C in air for 0.5 h. The obtained film was spin-coated further with an ethanol-based precursor solution containing identical metal acetates, and heat treated at 500 °C in air for 0.5 h. The X-ray diffraction pattern of the resultant film showed only peaks assignable to the layered-rock-salt LiCoO2. Raman spectroscopy measurements revealed vibrational modes assignable to layered rock salt LiCoO2, with minor content of less than 5 mol% of spinel-type Co3O4. The field emission scanning electron microscopy images indicated that the resultant film was 0.21 μm thick, had no voids, and was a combination of small rounded grains measuring 18 nm in diameter and hexagonal grains larger than 0.2 μm in length. The Hall effect measurements indicated that the resultant thin film was a p-type semiconductor with electrical resistivity of 35(2) Ω·cm and a carrier concentration and carrier mobility of 8(2) × 1016 cm−3 and 2(1) cm2·V−1·s−1, respectively.

show abstract

Application of carbonated apatite coating on a Ti substrate by aqueous spray method

Cited by 21 publications

References 34 publications

Synthesis and characterization of sol–gel derived calcium hydroxyapatite thin films spin-coated on silicon substrate

Synthesis and characterization of sol–gel derived calcium hydroxyapatite thin films spin-coated on silicon substrate

Ultrafast Oleophobic–Hydrophilic Switching Surfaces for Antifogging, Self-Cleaning, and Oil–Water Separation

Thin Film Fabrication and Characterization of Layered Rock Salt LiCoO2 on Quartz Glass Spray-Coated with an Aqueous Ammonia Solution Involving Metal Acetates

Contact Info

Product

Resources

About