Analysis of the buckling moment on rectangular hollow pipe under pure bending load

Yudo, Hartono; Amiruddin, Wilma; Jokosisworo, Sarjito

doi:10.1051/matecconf/201817701012

Cited by 2 publications

(1 citation statement)

References 4 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Research on hollow under pure bending pipes has been conducted by Yudo et al [7]. rectangular hollow pipes provide bending moments and geometric size variations.…”

Section: Introductionmentioning

confidence: 99%

The Critical Load on Quadrilateral and Circular Hollow Pipes under Pure Bending and Pure Torsion

Yudo,

Susilo,

Chrismianto

et al. 2023

Science and Engineering (EICSE 5th Edition)

Self Cite

View full text Add to dashboard Cite

Instability is one of the factors causing damage and injury that results in permanent disability. To increase the stable load-carrying capacity, a simplified and efficient computational method for determining the first critical load is necessary for the structure's structural design, application and safety. This study aims to determine the characteristics of the critical bending moment Mbcr and the critical torsion moment MTcr due to geometric size variations in the square, diamond, and circle cross-sectional hollow pipes so that consideration of the selection of hollow pipe size and cross-sectional shape is obtained under pure bending and pure torsion to minimize the occurrence of instability of the structure. The geometric size variation is carried out by changing the value of a/t in the quadrilateral pipe, the value of D/t in the circular pipe, and the length of the pipe L in each cross-sectional shape. This research was conducted using Finite Element Analysis-based software with linear and nonlinear buckling analyses. The moment load is given at the centre point of the model end, and the boundary conditions are set to see the deformation on the mid-span section of the pipe. The results showed that Mbcr and MTcr were inversely proportional to the values of a/t, D/t, and . The largest value of Mbcr belongs to the circular pipe. The value of Mbcr in the diamond pipe is greater than the square pipe but getting closer to the same as the value of L increases the MTcr value of both cross-sections is the same. The MTcr curve in the cross-section of the circle has a higher degree of steepness than the square and diamond cross-section. At the same value, the more the value of a/t and D/t increases thickness change has more compared to the circular pipe. At the same L, the greater the value of a/t and D/t, the difference in the Mbcr between the cross-section of the circle and the quadrilateral is smaller, but the difference in MTcr tends to be the same. At the same value of a/t and D/t, the oval deformation value and angle of twist will get bigger, but the Mbcr and MTcr values are getting smaller and will be constant at a given pipe length.

show abstract

“…Research on hollow under pure bending pipes has been conducted by Yudo et al [7]. rectangular hollow pipes provide bending moments and geometric size variations.…”

Section: Introductionmentioning

confidence: 99%

The Critical Load on Quadrilateral and Circular Hollow Pipes under Pure Bending and Pure Torsion

Yudo,

Susilo,

Chrismianto

et al. 2023

Science and Engineering (EICSE 5th Edition)

Self Cite

View full text Add to dashboard Cite

show abstract

Numerical evaluation of expansion loops for pipe subjected to thermal displacements

Yudo

Jokosisworo

Amiruddin

et al. 2021

Curved and Layered Structures

View full text Add to dashboard Cite

The thermal expansion can lead to the high stress on the pipe. The problem can be overcome using expansion loops in a certain length depending on the material’s elastic modulus, diameter, the amount of expansion, and the pipe’s allowable stresses. Currently, there is no exact definition for the dimension of expansion loops design both for loop width (W) and loop footing height (H) sizes. In this study, expansion loops were investigated with using ratio of width and height (W/H) variations to understand pipe stress occurring on the expansion loops and the expansion loops’ safety factor. Relationship between non dimensional stress on the expansion loop pipe was studied numerically by finite element software on several working temperatures of 400oF, 500oF, 600oF, and 700oF. It can be found that stress occurring on the pipes increases as the increases of W/H of the expansion loops and results in a lower safety factor. The safety factor of the expansion loops pipe has a value of 1 when the ratio of loop width and loop footing height (W/H) value was 1.2 for a 16-inch diameter pipe. Stress occurring on the pipe increases with the increase of the working temperature. Expansion loops pipe designed for 400oF can still work well to handle thermal extension pipe occurring on 500oF.

show abstract

Analysis of the buckling moment on rectangular hollow pipe under pure bending load

Cited by 2 publications

References 4 publications

The Critical Load on Quadrilateral and Circular Hollow Pipes under Pure Bending and Pure Torsion

The Critical Load on Quadrilateral and Circular Hollow Pipes under Pure Bending and Pure Torsion

Numerical evaluation of expansion loops for pipe subjected to thermal displacements

Contact Info

Product

Resources

About