Analysis of Stability in IEEE 14 Bus System using ETAP Software

Siva, A. Subramaniya; Sathieshkumar, S.; Kumar, T. Santhosh

doi:10.1109/icisc47916.2020.9171115

Cited by 8 publications

(3 citation statements)

References 9 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…He et al [39] examined the TS of a DC distribution network-connected distributed photovoltaic generator and generated a variable parameter control approach. Siva et al [40] built a hybrid PV/Wind system for TS analysis, power flow analysis, and P, Q correction in an IEEE 14 Bus system to decrease transmission losses, and fuel cost, and improve transmission line stability. Using a hybrid PSO-BFOA controller based on swarm optimization, the efficacy of wind and PV was evaluated to suppress and moderate global chaotic oscillations in a multi-machine system [41].…”

Section: Figure 6 Pv Inverter Modelmentioning

confidence: 99%

Utilizing Hybrid Renewable Energy Systems for Enhancing Transient Stability in Power Grids: A Comprehensive Review

Al-Kaoaz,

Alsammak

2023

JESA

View full text Add to dashboard Cite

The escalating demand for energy in recent years has been met with significant challenges, including resource scarcity and stringent environmental laws, which have curtailed the expansion of power generation and transmission capacity. As a result, the load borne by certain transmission lines has notably increased, which in turn raises concerns about the system's transient stability (TS). The rapid growth of renewable energy sources in power networks further compounds this issue. Despite sharing similar penetration levels, different renewable energy sources, such as wind and solar, and their combinations can have varied impacts on the system's TS. This paper conducts a comprehensive review of recent research and developments in power system TS. The focus is on the utilization of hybrid generating systems to address TS issues. The aim is to understand how different types of hybrid systems can enhance transient stability, with a comparative analysis on the advantages and disadvantages of each strategy. Furthermore, the role of Flexible AC Transmission System (FACTS) devices in improving transient stability is examined, along with the potential for synergistic use of both methods.

show abstract

Section: Figure 6 Pv Inverter Modelmentioning

confidence: 99%

Utilizing Hybrid Renewable Energy Systems for Enhancing Transient Stability in Power Grids: A Comprehensive Review

Al-Kaoaz,

Alsammak

2023

JESA

View full text Add to dashboard Cite

show abstract

“…The phasor measurement units (PMUs) placed at different locations generally at the ends of the line or at different bus locations. The optimal placement of PMU [14] is decided by different algorithms like genetic algorithm, particle swarm optimization (PSO), and artificial bee colony (ABC). Phasor measuring units [15] are the devices which measure the magnitude, frequency and phase of any voltage or current of a grid system synchronized with universal time coordinate (UTC).…”

Section: Phasor Measuring Unitmentioning

confidence: 99%

Power quality improvement and analysis of interconnected bus system with PMU using VSM-STATCOM

Kabra

Donepudi²

2022

IJAPE

View full text Add to dashboard Cite

The traditional static synchronous compensator (STATCOM) present in the power grid to compensate instability problem will not be not able to maintain stability of the system due to fluctuations in point of common coupling (PCC) voltage and frequency variation that may result in poor synchronization of the grid. The solution for this is the improvement in conventional STATCOM to virtual synchronous machine–static synchronous compensator (VSM-STATCOM). In this paper an interconnected IEEE-14 bus system is considered for analysis with VSM-STATCOM for improvement in voltage profile on weakest bus of the system. In order to find the weakest bus, load flow analysis is carried out on the bus system using Newton Rapson method. A VSM-STATCOM is connected at that weakest bus in synchronization to the grid injecting reactive power. For the analysis a fault is introduced on any of the line and voltage profile of the weakest bus is observed with and without VSM-STATCOM. The VSM-STATCOM is also compared to a conventional control STATCOM which has no inertia module. A comparative analysis is carrier out with parameters of voltage magnitude and frequency of the weak bus taken into consideration. The magnitude and frequency parameters of conventional STATCOM and VSM-STATCOM are measured using phasor measurement units. The model is designed using MATLAB Simulink power systems library block sets with graphical user interface (GUI) environment.

show abstract

“…Technology with PV and wind turbine installation techniques on a connected roof directly on the power grid using early streamer emission (ESE) technology in reducing the occurrence of lightning strikes. Therefore, before carrying out the installation, a more optimal relay coordination accuracy test is carried out with simulations and scenarios on the distribution network using electrical transient analyzer program (ETAP) software and also MATLAB software to see PV energy conversion [25]- [27]. The reliability of the installation of this technology will certainly increase consumer confidence in the installation of renewable energy, this is of course considering that the material and operational costs of the installation are very high so that it must be protected [28]- [30].…”

mentioning

confidence: 99%

Development of energy conversion and lightning strike protection simulation for photovoltaic-wind turbine on grid

Satria,

Mungkin,

Dayana

et al. 2024

IJECE

View full text Add to dashboard Cite

Photovoltaic (PV) installations and wind turbines that are installed on the rooftops of buildings need to be protected because the layout is in a high position and there is a risk of being struck by lightning. Therefore, a more effective protection system is designed to anticipate electronic damage and fire on all materials in the distribution network, especially the addition of PV and wind turbine installations on building roofs. The purpose of this study is to simulate a lightning protection system on the distribution network and the results of on-grid PV energy conversion using electrical transient analyzer program (ETAP) software. Feeder relay delay times and cascade coordination patterns between outgoing and incoming relays do not overlap. the delay time of the relay working on the feeder is 0.31 s and the coordination pattern of the outgoing relay and incoming relay does not touch each other, so the delay time for the incoming relay is 2.73 s. Then testing the results of PV energy conversion connected to the grid using MATLAB Simulink monitoring obtained data reaching 1.600 Wp at peak power with sun conditions parallel to the PV installation layout.

show abstract

Analysis of Stability in IEEE 14 Bus System using ETAP Software

Cited by 8 publications

References 9 publications

Utilizing Hybrid Renewable Energy Systems for Enhancing Transient Stability in Power Grids: A Comprehensive Review

Utilizing Hybrid Renewable Energy Systems for Enhancing Transient Stability in Power Grids: A Comprehensive Review

Power quality improvement and analysis of interconnected bus system with PMU using VSM-STATCOM

Development of energy conversion and lightning strike protection simulation for photovoltaic-wind turbine on grid

Contact Info

Product

Resources

About