Analysis of Electric Power Consumption by the Heat Pump Used in the Spray Booth

Nikończuk, P.; Tuchowski, Wojciech

doi:10.1007/978-981-15-8131-1_49

Cited by 3 publications

(2 citation statements)

References 16 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Due to a large amount of waste heat, its recovery should also be considered, which will significantly improve the energy efficiency of additive production. Heat recovery can be compared to heat recuperation in paint shops (Adamkiewicz and Nikończuk, 2019), spray booths, where the air is exchanged (Nikończuk, 2018;Nikończuk and Rosochacki, 2020) or the use of heat pumps that enable high efficiency (Nikończuk and Tuchowski, 2021).…”

Section: Figure 6 the Concept Of The Platform Cooperation Model For 3...mentioning

confidence: 99%

Additive Production Management in COVID-19 Pandemic

Piotr¹,

Królikowski²,

Strulak-Wójcikiewicz³

et al. 2022

ERSJ

View full text Add to dashboard Cite

Purpose:The article aims to discuss the authors' own experiences and literature review on the topic of small communities of additive production in COVID-19 conditions and propose an improvement of emergency procedures in situations of global threat. Design/Methodology/Approach: Its object is organizing and analyzing the experience gained during the production of healthcare products in 3D technology during the first wave of the COVID-19 pandemic. Findings: Further objects include identifying problems, proposing solutions, signaling problems to be solved, improving the efficiency of managing the production and distribution of health protection products, and improving the energy efficiency of the production process. Practical Implications: Structured conclusions and the resulting proposals for activities in the production and distribution of health protection products in situations of global life threat formulated further research goals.Originality/Value: An in-depth analysis of the literature on the subject and the research results presented in the article indicate the need for further research on the concept of optimization of the production process in the context of the temporary market demand for specific products. The article presents a proposal for a model that allows the use of incremental techniques and cost optimization depending on the market demands.

show abstract

Section: Figure 6 the Concept Of The Platform Cooperation Model For 3...mentioning

confidence: 99%

Additive Production Management in COVID-19 Pandemic

Piotr¹,

Królikowski²,

Strulak-Wójcikiewicz³

et al. 2022

ERSJ

View full text Add to dashboard Cite

show abstract

“…Due to the large amount of waste heat, its recovery should also be considered, which will significantly improve the energy efficiency of additive production. Heat recovery can be compared to heat recuperation in paint shops [66], in particular spray booths, where air is exchanged [67] or the use of heat pumps that enable high efficiency [68]. It is therefore reasonable to place in the platform a module with information on places with adequate ventilation and heat recovery, where there is a possibility of collective placement of printers.…”

Section: The Concept Of the Platform Cooperation Model For 3d Printin...mentioning

confidence: 99%

The concept of an e-platform cooperation model in the field of 3D printing during the COVID-19 pandemic

Strulak-Wójcikiewicz

Bohdan

2021

Procedia Computer Science

View full text Add to dashboard Cite

The COVID-19 pandemic has caused unprecedented public health and economic crises around the world. The protection of human health and life has become the most important challenge. Disrupted supply chains resulted in shortages in the supply of essential medical equipment and personal protective equipment. The quick response to this situation was the use of 3D printers for the production of this type of article, especially for the medical service. The initial experience presented in this article (the review of solutions and initiatives based on cooperation in the field of 3D printing during the first wave of the pandemic) showed the challenges faced by organizations engaged in 3D printing during the pandemic. The performed identification and compilation of the difficulties that occurred during cooperation in crisis conditions allowed the author of this article to present an original proposal to minimize the most important of these problems. The main purpose of the article is to present the concept of a cooperation model based on an internet platform in the field of 3D printing during the COVID-19 pandemic, which will allow to increase the efficiency of management of activities necessary in crisis conditions.

show abstract