An experimental verification on existence of air-drag force influencing yarn tension during rotor spinning

Abstract

Purpose Most researchers have neglected the effect air-drag force on yarn tension during rotor spinning. This paper aims to study the effect of rotor air-vacuum pressure in conjunction with opening roller speed and yarn linear density on the yarn tension generated during the rotor spinning, which has established their significant influences on both the mean and the peak tension.This is the first of one-of-a-kind experimental study being reported to demonstrate the influence of air-drag force on yarn tension during the rotor spinning under dynamic condition. Design/methodology/approach The dynamic measurements on yarn tension at the exit of the doffing tube were carried out by using an electronic capacitive yarn tension meter during rotor spinning. The derived experimental data were fitted into equations to construct the response equations and to work out the coefficients of multiple correlation between the data and the predicted equation for both the mean and the peak tension. Various surface plots were constructed by using those response surface equations, so as to study the effect of variables on yarn tension generated during the rotor spinning. Findings The study has established that the rotor vacuum is responsible in causing a change in yarn tension, it increases with the decrease in air-vacuum inside the rotor. The involvement of the opening roller speed in altering yarn tension during rotor spinning has been proved. As the opening roller speed changes, so does the air stream surrounding the opening roller speed with consequent alteration of the centrifugal force generated due to the rotation of the rotor. The centrifugal force and, hence, the yarn tension generated in the rotor will be simultaneously affected by both the rotor relative vacuum and the opening roller speed. Research limitations/implications This is a structured experimental study to verify the influence of air-drag force generated during rotor spinning on yarn tension. Very limited theoretical work has been carried out in this direction as reported in the introductory part of the paper. The result of the present study will encourage future researchers to revisit the theory on generation of air-drag force during rotor spinning and work out a new formula. Practical implications Next only to the conventional ring spinning system, the rotor spinning holds the second place in the share of global yarn production. Because of its advantage of lower cost of production and amenability to automation, the rotor spinning has gained acceptance in spun yarn production, particularly for spinning coarse and medium counts of yarns. Currently, it has acquired about 25 per cent share in the world’s spun yarn production. As many of the rotor machine variables significantly affect fibre configurations and, subsequently, the yarn properties by influencing the airflow characteristics inside the rotor unit, the study of yarn tension during rotor spinning and its analysis assumes a significance. Social implications Rotor spinning is a relatively new and faster method of conversion of discrete fibres into continuous staple yarn and, subsequently, various textiles and garments. Its yarn is distinct and a bit different compared to the conventional ring yarn. It has got wide acceptance in the market and fashion. As such, the spinning sector that converts fibres into yarns is an important industry world over, providing employment to many. Besides, being the basic operation in the fibre value chain, it supports many downstream activities, including human clothing and fashion. Thus, the research on rotor spinning, particularly the yarn engineering to produce better products will be helpful to strengthen and grow the textile value chain. Originality/value This is an original research study. The magnitude and the direction of the air drag on the yarn during rotor spinning is very difficult to assess. Thus, most researchers for the sake of simplicity in analysis have neglected its effect on yarn dynamics, but a few of them have taken note of it in their theoretical propositions. However, no experimental result has been reported so far in the literature, supporting the influence of such air-drag force on yarn tension in the rotor spinning. In fact, none of the above studies have considered the induced effect of centrifugal force caused because of the rotation of the opening roller on the airstream that flows from the transfer channel inlet into the rotor because of its partial vacuum, causing consequential effects on air-drag force and tension in the yarn inside the rotating rotor. This is the first of one-of-a-kind experimental study being reported to demonstrate the influence of air-drag force on yarn tension during the rotor spinning under dynamic condition.

Numerical simulation of airflow field in rotor spinning channel based on dynamics optimization

“…), open-end spinning could achieve the process of fiber collecting, twisting and yarn exporting by the airflow produced by the rotor at high speed, which is characterized by short procedure, high speed, large package and other advantages. 8 As shown in Figure 1, after the cotton silver was placed into the spinning apparatus by the bell mouth, it would be converted into the even fibre strand on being pressed by the feed roller and feed plate, after which it would be decomposed; the combing roller would decompose the cotton strand and remove impurities. Under the function of airflow and centrifugal force, the decomposed single fiber rapidly entered the fiber pipeline, which slipped, collected and twisted the fiber under the condition of high-speed rotation.…”

“…The numerical simulation of the flow field in the spinning channel was conducted in FLUENT software. Based on the spinning process of the air-extraction rotor, the airflow inlet of the fiber pipeline was set as the form of mass flow rate, then the airflow mass m entering the fiber pipeline within the unit time could be calculated as per equaltion (8). 19 Given that the atmosphere density q ¼ 1.225 kg/m 3 , inlet region area s ¼ 29.63 mm 2 , inlet airflow velocity v ¼ 55 m/s were all introduced into equation ( 8), then the inlet mass flow rate m % 0.002 kg/s was obtained.…”

The energy consumption prediction of the direct cabling machine based on balloon theory

“…Another part of the research focused on applying the balloon theory to existing textile equipment Praček 7 improved the unwinding process of cross winding bobbin and improves the unwinding stability based on the balloon theory. Chattopadhyay et al 8 investigated the effect of air resistance generated by vacuum pressure, Cairo roll speed and yarn linear density on the tension of the balloon during rotor spinning. Mei 9 studied the influence of spindle angular velocity, yarn fineness and other factors on the tension of balloon of direct cabling machine, and established the fitting equation.…”

Optimization analysis of combing box for air yarn based on computational fluid dynamics

“…In order to obtain better spinning performance, experimental studies on the design of combing units have been carried out over the last decades. 6 –8 Yuksekkaya et al 9 and Shang et al 10 studied fiber removal from open rolls and fiber trajectories in the transfer channel using a high-speed camera and scanning electron microscopy. Their analysis concluded that a narrow rectangular cross section of the transfer channel was more conducive to producing a better fiber structure than a rounded transfer channel.…”