An experimental investigation into the effect of process conditions on the mass concentration of cutting fluid mist in turning

Gunter, Kenneth L.; Sutherland, John W.

doi:10.1016/s0959-6526(99)00150-x

Cited by 58 publications

(22 citation statements)

References 8 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Liquid aerosols can be generated in several industrial machining processes (Boundy et al, 2000;Cooper and Leith, 1998;Gunter and Sutherland, 1999;Simpson et al, 2000). These mists can be formed by different mechanisms.…”

Section: Introductionmentioning

confidence: 99%

Experimental and modelled efficiencies during the filtration of a liquid aerosol with a fibrous medium

Charvet

Gonthier

Gonze

et al. 2010

Chemical Engineering Science

View full text Add to dashboard Cite

Section: Introductionmentioning

confidence: 99%

Experimental and modelled efficiencies during the filtration of a liquid aerosol with a fibrous medium

Charvet

Gonthier

Gonze

et al. 2010

Chemical Engineering Science

View full text Add to dashboard Cite

“…With a milling simulation software, Dagiloke et al (6) developed an optimized milling model for use in actual machining. Diniz (7), (8) found that if the feed rate and the nose radius of the cutter were increased and that the cutting speed was reduced, dry machining would not affect tool life and machining time. On the contrary, the surface roughness and energy efficiency would be improved.…”

Section: Introductionmentioning

confidence: 99%

Optimization of the High-Speed CNC Milling Process Using Two-Phase Parameter Design Strategy by the Taguchi Methods

Tzeng

Chen

2005

JSME Int. J., Ser. C

View full text Add to dashboard Cite

High speed, high quality and short delivery are the development trend of the manufacturing industry. In this paper, the Taguchi dynamic characteristic theory was used coupled with proposed ideal function models under a two-phase optimization strategy. The main objective of this work is to develop optimized machining parameters in the high-speed milling process with the characteristics of high machining efficiency and geometrical accuracy, and wide applications. The experimental results showed that the machining time can be effectively reduced using the designed optimal parameters obtained from the first phase of the strategy. The process variance was only 63.96% of the initial conditions, and the robustness of the process was increased 1.56 times. The control factors having the most influences on the machining time and the robustness of the CNC milling process in order of importance were identified as cutting speed, number of teeth, and feed per tooth. The dimensional relationship between the input and output of the milling process under the first-phase optimized conditions was derived as Y = 1.001 090M. Therefore, according to this model, final adjustment to the input programmed dimension can be made in phase two to obtain the ideal machining accuracy.

show abstract

“…By forsaking customary cooling greases and utilizing the advances of dry machining or least amount oil (MQL), this cost part can be decreased essentially. Other than a change in the proficiency of the creation procedure, such an innovation change makes a commitment to the assurance of work [16][17][18] and the earth [19,20]. The decrease of considerable introduction to cooling ointments at the work put lessens the perils and enhances the work result in the meantime.…”

mentioning

confidence: 99%

“…The decrease of considerable introduction to cooling ointments at the work put lessens the perils and enhances the work result in the meantime. Moreover, a venture can utilize eco-accommodating generation forms, which prompts a superior picture in the market [17][18][19][20][21][22][23][24][25][26][27][28]. Investigating and understanding the cutting procedure components is a key issue in building up a sparing and safe dry machining process.…”

mentioning

confidence: 99%

Multi Response Optimization of Setting Input Variables for Getting Better Product Quality in Machining of Magnesium AM60 by Grey Relation Analysis and ANOVA

Sivam

Karuppaiah

Yedida

et al. 2018

Period. Polytech. Mech. Eng.

View full text Add to dashboard Cite

show abstract

An experimental investigation into the effect of process conditions on the mass concentration of cutting fluid mist in turning

Cited by 58 publications

References 8 publications

Experimental and modelled efficiencies during the filtration of a liquid aerosol with a fibrous medium

Experimental and modelled efficiencies during the filtration of a liquid aerosol with a fibrous medium

Optimization of the High-Speed CNC Milling Process Using Two-Phase Parameter Design Strategy by the Taguchi Methods

Multi Response Optimization of Setting Input Variables for Getting Better Product Quality in Machining of Magnesium AM60 by Grey Relation Analysis and ANOVA

Contact Info

Product

Resources

About