An efficient approach to separate CO2 using supersonic flows for carbon capture and storage

Wen, Chuang; Karvounis, Nikolas; Walther, Jens Honoré; Yan, Yuying; Feng, Yuqing; Yang, Yan

doi:10.1016/j.apenergy.2019.01.062

Cited by 106 publications

(33 citation statements)

References 46 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The pressure-velocity coupling we used was the phase-coupled SIMPLE algorithm. The continuity equation, momentum equations, and turbulence equations were discretized with the second-order upwind scheme [40,41].…”

Section: Numerical Schemesmentioning

confidence: 99%

Sand Transport and Deposition Behaviour in Subsea Pipelines for Flow Assurance

2019

Self Cite

View full text Add to dashboard Cite

Sand transport through tubing and pipeline could cause a series of problems to flow assurance, if not properly managed or controlled. The most serious problem is the accumulation and erosion in multiphase flow pipelines and the surface equipment. Therefore, the importance of understanding the transport and deposition behaviour of sands through multiphase flow pipelines cannot be overemphasized. This study presents the sand transport and deposition characteristics in the complicated multiphase flow pipeline. The numerical result shows that the slurry velocity presents a uniform distribution in the multiphase flow pipeline at the sand concentration of 5% and the sand diameter of 50 µm. However, the slurry velocity at the bottom of the pipeline is significantly smaller than that at the top when the sand concentration and diameter reach 30% and 300 µm, respectively. It indicates that the sand deposition at the bottom of the pipe declines the slurry velocity and transport capacity. The deposition thickness is approximately 10% of the pipe diameter even at the low concentration of 5% sand with a small sand diameter of 50 µm and a high slurry velocity of 1.8 m/s. The sand deposition reaches about 30% of the pipe diameter at the same low concentration and high slurry velocity when the sand diameter increases to 300 μm.

show abstract

Section: Numerical Schemesmentioning

confidence: 99%

Sand Transport and Deposition Behaviour in Subsea Pipelines for Flow Assurance

2019

Self Cite

View full text Add to dashboard Cite

show abstract

“…The inlet of cascade is the boundary condition of total pressure inlet, and the outlet of cascade is the boundary condition of pressure outlet. The blade surface, hub and shroud are the boundary condition of wall (Han et al, 2020;Wen et al, 2019). And the channel part of cascade is the periodic boundary condition.…”

Section: Physical Model Constructionmentioning

confidence: 99%

Numerical investigation of the wet steam condensation flow characteristics in stator cascade with blade surface heating

Han

Yuan

Zhao

et al. 2020

Engineering Applications of Computational Fluid Mechanics

View full text Add to dashboard Cite

The scientific and effective control of steam wetness in steam turbines is of great significance for improving power generation efficiency. Based on the research status of wet steam, the influence of different surface heating intensity in a stator cascade was studied. The distribution of condensation flow parameters in White cascade under 0-700 kW/m 2 surface heating intensity is calculated. On this basis, the positive heating intensity region was determined and refined to obtain the best heating condition with higher accuracy. The results show that the condensation is restrained and the outlet wetness is decreased as the blade surface heating intensity increases. The steam wetness and droplet diameter in the flow field can be controlled by adding heating intensity. Additionally, at the initial stage of applying heat to the blade, an increasing enthalpy drop occurs, and the entropy increase experiences a decline, while negative effects rapidly emerge if the heating intensity is too high. The optimum heating intensity is 120 kW/m 2. Compared with the 0 kW/m 2 , the average outlet wetness, total pressure loss coefficient and entropy increase of 120 kW/m 2 surface heating intensity can be reduced by 1.1266%, 15.5% and 1.7%, respectively, and the enthalpy drop can be increased by 1.7%.

show abstract

“…As for the non-equilibrium state in supersonic flows, the nucleation and condensation of condensable gases are overwhelmingly complicated [41,42]. Based on the single-fluid Eulerian model [41], several assumptions were implemented to ensure the simulation was numerically stable and efficient.…”

Section: Wet Steam Modelingmentioning

confidence: 99%

Computational Study of Wet Steam Flow to Optimize Steam Ejector Efficiency for Potential Fire Suppression Application

Yuen

Chen

et al. 2019

Applied Sciences

View full text Add to dashboard Cite

The steam ejector is a core component of an ejector-based refrigeration system. Additionally, steam ejectors can also be potentially applied for a fire suppression system by using pressurized steam droplets to rapidly quench and extinguish the fire. The use of steam will significantly reduce the amount of water consumption and pipe flow rate compared to conventional sprinklers. However, the efficiency of the steam ejector nozzle is one of major factors that can influence the extinguishing mechanisms and the performance of pressurized steam for fire suppression. In this article, to formulate an assessment tool for studying the ideal entrainment ratio and initial flow wetness, a wet steam model has been proposed to enhance our understanding of the condensation and evaporation effects of water droplets from a numerical perspective. The entire steam-ejector system including the nozzle, mixing chamber, throat and diffuser were modeled to study the profiles in axial pressure and temperature across the system, and were compared with self-measured experimental data. In addition, the flow and heat transfer interactions between the fluid mixture and nucleating water droplets were numerically examined by comparing initial conditions with different liquid fractions, as opposed to the ideal gas assumption. With the application of the proposed wet-steam model, the numerical model showed vast improvement in the axial pressure distribution over the ideal gas model. Through numerical conditions, it was found that reducing the wetness of the secondary inlet flow will potentially optimize the system performance with a significant increase of the entrainment ratio from 0.38 to 0.47 (i.e., improvement of around 23%).

show abstract

An efficient approach to separate CO2 using supersonic flows for carbon capture and storage

Cited by 106 publications

References 46 publications

Sand Transport and Deposition Behaviour in Subsea Pipelines for Flow Assurance

Sand Transport and Deposition Behaviour in Subsea Pipelines for Flow Assurance

Numerical investigation of the wet steam condensation flow characteristics in stator cascade with blade surface heating

Computational Study of Wet Steam Flow to Optimize Steam Ejector Efficiency for Potential Fire Suppression Application

Contact Info

Product

Resources

About