Alloy Design and Characterization of γ′ Strengthened Nickel-based Superalloys for Additive Manufacturing

Abstract

Nickel-based superalloys, an alloy system bases on nickel as the matrix element with the addition of up to 10 more alloying elements including chromium, aluminum, cobalt, tungsten, molybdenum, titanium, and so on. Through the development and improvement of nickel-based superalloys in the past century, they are well proved to show excellent performance at the elevated service temperature. Owing to the combination of extraordinary high-temperature mechanical properties, such as monotonic and cyclic deformation resistance, fatigue crack propagation resistance; and high-temperature chemical properties, such as corrosion and oxidation resistance, phase stability, nickel-based superalloys are widely used in the critical hot-section components in aerospace and energy generation industries. The success of nickel-based superalloy systems attributes to both the well-tailored microstructures with the assistance of carefully doped alloying elements, and the intently developed manufacturing processes. The microstructure of the modern nickel-based superalloys consists of a two-phase configuration: the intermetallic precipitates (Ni,Co)3(Al,Ti,Ta) known as γ′ phase dispersed into the austenite γ matrix, which is firstly introduced in the 1940s. The recently developed additive manufacturing (AM) techniques, acting as the disruptive manufacturing process, offers a new avenue for producing the nickel-based superalloy components with complicated geometries. However, γ′ strengthened nickel-based superalloys always suffer from the micro-cracking during the AM process, which is barely eliminated by the process optimization. On this basis, the new compositions of γ′ strengthened nickel-based superalloy adapted to the AM process are of great interest and significance. This study sought to design novel γ′ strengthened nickel-based superalloys readily for AM process with limited cracking susceptibility, based on the understanding of the cracking mechanisms. A two-parameter model is developed to predict the additive manufacturability for any given composition of a nickel-based superalloy. One materials index is derived from the comparison of the deformation-resistant capacity between dendritic and interdendritic regions, while another index is derived from the difference of heat resistant capacity of these two spaces. By plotting the additive manufacturability diagram, the superalloys family can be categorized into the easy-to-weld, fairly-weldable, and non-weldable regime with the good agreement of the existed knowledge. To design a novel superalloy, a Cr-Co-MoW -Al-Ti-Ta-Nb-Fe-Ni alloy family is proposed containing 921,600 composition recipes in total. Through the examination of additive manufacturability, undesired phase formation propensity, and the precipitation fraction, one composition of superalloy, MAD542, out of the 921,600 candidates is selected. Validation of additive manufacturability of MAD542 is carried out by laser powder bed fusion (LPBF). By optimizing the LPBF process parameters, the crack-free MAD542 part is achieved. I...

Fatigue Driving Detection Method Based on IPPG Technology

“…The results show that the ratio of LF to HF will increase in the fatigue state. When LF/HF is between 0 and 3, the human body is awake; when LF/HF is greater than 3, the human body is in a state of fatigue [28]. The conclusion is in good agreement with this experiment.…”

“…The scatter points in Figure 4.6 spread out around the 45° line, indicating that the driver has sinus arrhythmia and is in a state of fatigue. Studies show that under normal circumstances, the ratio of SD1/SD2 is around 0.25, but when the human body is in a state of mental fatigue, this ratio will show an upward trend and is significantly greater than 0.25 [28]. Laurent Mourot et al evaluated the effectiveness of the Poincare graph analysis.…”

“…Finally, the fatigue of the driver is judged according to the index. According to the result in Chapter 4, when the human body is in a state of fatigue, the frequency domain indices and nonlinear indices show an obvious upward trend, and the fatigue of the human body can be clearly judged according to the relevant literature [28][29][30][31]. In this study, the IPPG technology was used to realise non-contact driver fatigue detection to ensure safe and healthy driving.…”

Modelling of Additive Manufacturability of Nickel-Based Superalloys for Laser Powder Bed Fusion

“…In this study, f DC is taken as 70% as the DC volume fraction, where 30% is used as the ID fraction f ID . This assignment corresponds very well to the DC and ID fractions determined via image analysis from the previous investigation [62] in an area fraction manner. Furthermore, among different nickel-based superalloys in the as-LPBF-processed state (see Fig.…”

Multi-length-scale study on the heat treatment response to supersaturated nickel-based superalloys: Precipitation reactions and incipient recrystallisation

“…The onset of static recrystallisation occurs within minutes, whereas it takes hours for the material to achieve full recrystallisation. The resultant microstructure with reduced anisotropy and larger grain sizes, nevertheless, faces a universal ductility challenge as evidenced in multiple superalloy systems [13,72,73,74,75]. Future work to understand the root cause of the embrittlement and strategies for mitigation is needed.…”