Abstract:In this study, the effects of multi-perforated gypsum boards on floor impact noises were investigated in a box-type test building and an actual apartment building. In a box-type test building with 150 mm thick slab, various design factors such as hole pattern, hole size, opening ratio, backing, or finishing materials were considered. Heavy-weight impact sources of bang machine and rubber ball were employed. The test procedure followed KS F 2810-2, and then, a single number rating was derived in accordance with… Show more
“…The progress of developing ceiling structures in receiving rooms to reduce noise from floor impacts is also underway [21][22][23][24][25][26]. This involves using internal acoustic materials to minimize the amplification of impact noises to the room below due to the influence of the air layer within the ceiling, and a ceiling-less design to minimize the transmission of impact noises through the ceiling.…”
Floor mats are commonly used to improve the impact sound performance of existing homes, but the actual reduction does not consistently appear depending on the test-bed conditions used to determine it. Therefore, this study evaluated the effects of the environmental conditions of the test-bed on the impact sound reduction performance of different floor mats. The Korean Industrial Standard, KS F 2865, specifies the measurement method in the test room and sets the thickness range of the available target floor structure from bare slab 120 mm to 210 mm. The evaluation method is ∆?, which is the difference in standardized impact sound levels before and after the installation of the floor finishing material. In this study, a total of eight types of floor mats were tested in four different test-beds according to KS F 2865. The impact sources used were tapping, bang machines and a rubber ball to consider both light-weight and heavy-weight impact sounds. The results were derived as impact sound reduction performance for each frequency band and a single number quantity. The results showed that light impact sound had a similar minimum reduction characteristic of at least 38 dB, regardless of the floor structure on which the mat was installed. However, the heavy-weight impact sound showed different tendencies depending on the floor mat and the characteristics of the floor structure of the test-bed when a bang machine and a rubber ball were used. In particular, the reduction by the bang machine showed less than half the tendency of the reduction by the rubber ball, and the tendency of the heavy-weight impact sound to be reduced depending on the floor mat was maintained, but the reduction differed depending on the test bed. The reduction was larger in the box-type test room than in the real-life type test room, and among the box-type test rooms, the one with a thicker bare slab showed a relatively larger reduction. In addition, the reliability of the measurement results was discussed through the correlation analysis between the single number quantities depending on the thickness of the bare slab of the test-beds.
“…The progress of developing ceiling structures in receiving rooms to reduce noise from floor impacts is also underway [21][22][23][24][25][26]. This involves using internal acoustic materials to minimize the amplification of impact noises to the room below due to the influence of the air layer within the ceiling, and a ceiling-less design to minimize the transmission of impact noises through the ceiling.…”
Floor mats are commonly used to improve the impact sound performance of existing homes, but the actual reduction does not consistently appear depending on the test-bed conditions used to determine it. Therefore, this study evaluated the effects of the environmental conditions of the test-bed on the impact sound reduction performance of different floor mats. The Korean Industrial Standard, KS F 2865, specifies the measurement method in the test room and sets the thickness range of the available target floor structure from bare slab 120 mm to 210 mm. The evaluation method is ∆?, which is the difference in standardized impact sound levels before and after the installation of the floor finishing material. In this study, a total of eight types of floor mats were tested in four different test-beds according to KS F 2865. The impact sources used were tapping, bang machines and a rubber ball to consider both light-weight and heavy-weight impact sounds. The results were derived as impact sound reduction performance for each frequency band and a single number quantity. The results showed that light impact sound had a similar minimum reduction characteristic of at least 38 dB, regardless of the floor structure on which the mat was installed. However, the heavy-weight impact sound showed different tendencies depending on the floor mat and the characteristics of the floor structure of the test-bed when a bang machine and a rubber ball were used. In particular, the reduction by the bang machine showed less than half the tendency of the reduction by the rubber ball, and the tendency of the heavy-weight impact sound to be reduced depending on the floor mat was maintained, but the reduction differed depending on the test bed. The reduction was larger in the box-type test room than in the real-life type test room, and among the box-type test rooms, the one with a thicker bare slab showed a relatively larger reduction. In addition, the reliability of the measurement results was discussed through the correlation analysis between the single number quantities depending on the thickness of the bare slab of the test-beds.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.