Accuracy of Four Removable Die Techniques

Dilts, Walter E.; Podshadley, Arlon G.; Sawyer, H.F.; Neiman, Robert

doi:10.14219/jada.archive.1971.0420

Cited by 10 publications

(7 citation statements)

References 5 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…This was in agreement with the result of the other investigators. 2,3,[12][13][14][15][16][17] This difference indicated the amount of vertical and horizontal displacements of each die within a group. The displacement exhibited both a positive value and a negative value.…”

Section: Discussionmentioning

confidence: 99%

“…This was similar to the results obtained in the previous studies. 2,3,12,14 The displacement of the dies can be attributed to:…”

Section: Discussionmentioning

confidence: 99%

“…1,2 This is important in order to maintain an accurate relationship between the prepared teeth, adjacent, and opposing teeth to obtain a cast restoration that has correct occlusal and proximal contours as well as marginal fit. 3 Over a period of time, various concepts and techniques have been advocated for making removable die systems. 4 Positional shift in the horizontal and vertical directions has been observed in most of the existing systems.…”

Section: Introductionmentioning

confidence: 99%

See 2 more Smart Citations

Evaluation of Relative Accuracy of Three Commercially Available Removable Die Systems of Different Configurations: An in vitro Study

Pasam¹,

Arora²,

Gupta³

et al. 2017

Journal of Oral Health and Community Dentistry

View full text Add to dashboard Cite

Introduction:The positional shift observed in removable die systems before and after sectioning the master cast may result in a cast restoration with improper occlusal and proximal contacts and marginal fit, thereby requiring time-consuming chairside adjustments.Aim: This study was done to evaluate the relative accuracy of three commercially available removable die systems with different configurations by measuring the average die displacement before and after sectioning of the cast. Materials and methods:A total of 60 impressions were made of the standardized brass master model using polyvinylsiloxane. Impressions were divided into three groups. For each group, a different removable die system was used. Group I: cross pin; group II: M R pin; and group III: conventional brass dowel pin. The presectioning measurement both in the horizontal and vertical directions of all the 60 casts obtained were made using profile projector. The casts were then sectioned and removed and replaced 30 times, and the postsectioning measurements were made using the same references. The differences between the presectioning and the postsectioning measurements were calculated Statistical analysis used: The data were analyzed using analysis of variance (ANOVA) and Tukey's multiple comparison test.Results: All the three die systems exhibited displacement both in the horizontal and vertical directions before and after sectioning the casts. Brass dowel pin exhibited the greatest amount of displacement both in the horizontal and vertical directions. Conclusion:The use of more than one pin and the presence of metallic or plastic sleeves can result in improved accuracy and stability of the die system.

show abstract

Section: Discussionmentioning

confidence: 99%

“…This was similar to the results obtained in the previous studies. 2,3,12,14 The displacement of the dies can be attributed to:…”

Section: Discussionmentioning

confidence: 99%

Section: Introductionmentioning

confidence: 99%

See 1 more Smart Citation

Evaluation of Relative Accuracy of Three Commercially Available Removable Die Systems of Different Configurations: An in vitro Study

Pasam¹,

Arora²,

Gupta³

et al. 2017

Journal of Oral Health and Community Dentistry

View full text Add to dashboard Cite

show abstract

“…Study of the relevant literature highlights the importance of a precise master cast. [1][2][3] To eliminate any discrepancies in fit, it is essential to work on a master cast that reproduces as accurately as possible the exact positions of dental or implant abutments in the patient's mouth. The type and property of die materials, such as dimensional accuracy, detail reproduction, abrasion resistance, and hardness, have been investigated in the dental literature.…”

Section: Discussionmentioning

confidence: 99%

“…The master casts on which fixed prostheses are fabricated must properly reproduce an abutment whether the case involves a single unit or multiple units in an entire arch rehabilitation. [1][2][3] They must achieve certain specifications with respect to dimensional accuracy, detail reproduction, surface hardness, abrasive resistance, compatibility with impression materials, transverse strength, ease of manipulation, and lack of toxicity. 4 Improved dental stone and epoxy resin are the most popular materials in dentistry for constructing master casts for fixed prostheses, even though a resin-reinforced gypsum product, a polyurethane resin, and silver and copper electroplated die systems have all been used.…”

mentioning

confidence: 99%