Abrasive Wear Behavior of Granite-Filled Glass-Epoxy Composites by SiC Particles Using Statistical Analysis

Basavarajappa, S.; Yadav, S. Manjunath; Kumar, Santosh; Arun, K.V.; Narendranath, S.

doi:10.1080/03602559.2010.543734

Cited by 15 publications

(8 citation statements)

References 26 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…To enhance the friction and wear properties of the epoxy polymer matrix, reinforcing fillers such as fiber, particulate, nanoscale particles are commonly used [5][6][7][8][9][10] .…”

Section: Introductionmentioning

confidence: 99%

Tribological Properties of Epoxy/Aramid Fabric Composites Reinforced by Boron Nitride of Single Layer

Pan

Wang

et al. 2014

Polymer-Plastics Technology and Engineering

View full text Add to dashboard Cite

Epoxy composite coatings filled with boron nitride of single layer (SBN) were prepared through a dip-coating method. The friction and wear behaviors of the coatings were performed, and the results showed that the wear life of composite coatings was obviously higher than that of pristine coating with low SBN content; however, friction coefficients only decreased slightly. The optimal content of SBN was 3 wt.%, and the wear life of the composite coating increased by 179% compared with that of pristine coating. The morphology of worn surfaces was studied, and the wear mechanisms were discussed.

show abstract

“…To enhance the friction and wear properties of the epoxy polymer matrix, reinforcing fillers such as fiber, particulate, nanoscale particles are commonly used [5][6][7][8][9][10] .…”

Section: Introductionmentioning

confidence: 99%

Tribological Properties of Epoxy/Aramid Fabric Composites Reinforced by Boron Nitride of Single Layer

Pan

Wang

et al. 2014

Polymer-Plastics Technology and Engineering

View full text Add to dashboard Cite

show abstract

“…Agrawal et al [7] reported that factors particle size and filler content highly affect the specific wear rate of glass fiber (20 wt.%) reinforced epoxy matrix composite with silicon carbide (SiC) filler (0, 5, 10, 15, and 20 wt.%). Basavarajappa et al [8] investigated the sliding wear behavior of glass fiber (20 and 60 wt.%) reinforced epoxy matrix composites with granite powder (40 wt.%) as filler. It was reported that granite powder as a filler significantly improved the wear resistance of the glass-epoxy composites.…”

Section: Introductionmentioning

confidence: 99%

Mechanical andthree‐bodyabrasive wear behavior analysis of glass and basaltfiber‐reinforcedepoxy composites

et al. 2020

View full text Add to dashboard Cite

This research article presents the comparative investigation of physical, mechanical, and abrasive wear behavior of chopped glass and basalt fiber‐reinforced epoxy composites. The composites were fabricated by hand lay‐up technique. The fiber (glass and basalt) was varied in the range of 10 to 40 wt.% in the composite at an interval of 10 wt.% to find out the physical (density and void content), mechanical (tensile strength, flexural strength, and impact strength), and steady state abrasive wear rate, respectively. The Taguchi's design of experiment method was used for designing of experimental runs having input controlling variables like sliding distance, normal load, fiber content, and abrasive size. This study clearly demonstrated that with increase the fiber content, the density and void content of both fiber (glass and basalt) reinforced composite were increased. The basalt fiber‐reinforced composites show lesser voids than glass fiber‐reinforced composites. The tensile strength, flexural strength, and impact strength of both composites increased with increase the fiber content whereas glass fiber‐reinforced composites show slightly lower tensile strength, flexural strength, and impact strength than basalt fiber‐reinforced composites. However, as far as basalt fiber‐reinforced composites show better wear resistance than glass fiber‐reinforced composites.

show abstract

“…Also, in a review of some of the literature concerning hybrid composites, Basavarajappa et al [6] investigated abrasive wear behavior of granite-filled glass-epoxy composites by SiC particles using statistical analysis. Kaushik et al [7] prepared and characterized graphite flake-filled polyester composites.…”

Section: Introductionmentioning

confidence: 99%

Studies on Mechanical and Fractographic Behavior of Polycarbonate-Toughened Epoxy-Granite Particle Hybrid Composites

Rama

Pavithra

2013

Polymer-Plastics Technology and Engineering

View full text Add to dashboard Cite

Epoxy resin based on diglycidyl ether of bisphenol-A (DGEBA type) was toughened with varying weight fractions, i.e., from 0 to 10% of thermoplastic polycarbonate (PC). Compression and impact properties of the toughened resin matrix were investigated. Epoxy containing 6 wt% of PC showed highest strength and modulus. Further, composites were prepared with varying percentage viz., 30 to 60 wt% of silane coupling agent treated granite particle (TGP) loading with 6 wt% PC toughened epoxy resin as matrix. Mechanical properties such as compression and impact behaviour of these composites were assessed and catalogued. Fractographic studies of the composites have been carried out using scanning electron microscopy (SEM).

show abstract

Abrasive Wear Behavior of Granite-Filled Glass-Epoxy Composites by SiC Particles Using Statistical Analysis

Cited by 15 publications

References 26 publications

Tribological Properties of Epoxy/Aramid Fabric Composites Reinforced by Boron Nitride of Single Layer

Tribological Properties of Epoxy/Aramid Fabric Composites Reinforced by Boron Nitride of Single Layer

Mechanical andthree‐bodyabrasive wear behavior analysis of glass and basaltfiber‐reinforcedepoxy composites

Studies on Mechanical and Fractographic Behavior of Polycarbonate-Toughened Epoxy-Granite Particle Hybrid Composites

Contact Info

Product

Resources

About