A systematic literature review on the Digital Twin of the factory in the context of the product and factory lifecycle

Cieply, Jonas; Disselkamp, Jan-Philipp; Dyck, Florian; Alturk, Waddah; Kühn, Dr.-Ing. Arno; Dumitrescu, Prof. Dr.-Ing. Roman

doi:10.1016/j.procir.2023.02.168

Cited by 3 publications

(2 citation statements)

References 30 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The term DFT is defined differently in the literature. There are studies that have analysed the distinction between the term DFT and similar terms, for example as part of an SLR (Cieply et al, 2023). The discussion on the differentiation from other terms primarily centres on the extent to which data is exchanged between the physical and cyber worlds.…”

Section: Definition Of Termsmentioning

confidence: 99%

See 1 more Smart Citation

Towards the digital factory twin – design guide for creating a 3D factory model

Disselkamp,

Grothe,

Lick

et al. 2024

Proc. Des. Soc.

View full text Add to dashboard Cite

Shorter product lifecycles are also leading to even shorter planning times for the development of production systems. In most companies, the restructuring is carried out within a few weeks during the annual holidays. Digital tools such as simulations or the digital twin are used to avoid delaying the restructuring during this time. However, the introduction of a 3D model of the factory is often the first point of failure for many companies. This article proposes a six-step process model that enables the transition from 2D to 3D design. The process model was evaluated in a research project.

show abstract

Section: Definition Of Termsmentioning

confidence: 99%

“…The digital shadow has an automatic link between the physical and cyber worlds, but a manual link between the cyber and physical worlds. In comparison, the digital twin has an automatic link in both directions (Cieply et al, 2023).…”

Section: Definition Of Termsmentioning

confidence: 99%

Towards the digital factory twin – design guide for creating a 3D factory model

Disselkamp,

Grothe,

Lick

et al. 2024

Proc. Des. Soc.

View full text Add to dashboard Cite

show abstract

Interoperability of heterogeneous Systems of Systems: from requirements to a reference architecture

Sadeghi,

Carenini,

Corcho

et al. 2023

J Supercomput

View full text Add to dashboard Cite

Interoperability stands as a critical hurdle in developing and overseeing distributed and collaborative systems. Thus, it becomes imperative to gain a deep comprehension of the primary obstacles hindering interoperability and the essential criteria that systems must satisfy to achieve it. In light of this objective, in the initial phase of this research, we conducted a survey questionnaire involving stakeholders and practitioners engaged in distributed and collaborative systems. This effort resulted in the identification of eight essential interoperability requirements, along with their corresponding challenges. Then, the second part of our study encompassed a critical review of the literature to assess the effectiveness of prevailing conceptual approaches and associated technologies in addressing the identified requirements. This analysis led to the identification of a set of components that promise to deliver the desired interoperability by addressing the requirements identified earlier. These elements subsequently form the foundation for the third part of our study, a reference architecture for interoperability-fostering frameworks that is proposed in this paper. The results of our research can significantly impact the software engineering of interoperable systems by introducing their fundamental requirements and the best practices to address them, but also by identifying the key elements of a framework facilitating interoperability in Systems of Systems.

show abstract

Research on data mapping and fusion method of ship production workshop based on digital twins

Wang,

Chen,

Zhang

et al. 2024

Measurement and Control

View full text Add to dashboard Cite

Aiming at the problems existing in discrete manufacturing workshops of ships, such as the lack of real-time management and control ability of on-site production status, and the long time delay of real-time interaction and fusion between physical entities and virtual entities data, this paper proposes ship production workshop data mapping and fusion method based on digital twins. Taking a ship machining workshop as an application research example, the integrated business process and data mapping and fusion method of the machining workshop based on digital twins are studied. On this basis, the dynamic scheduling optimization algorithm of ship machining workshops based on digital twins is studied. The results show that the data mapping and fusion method in this study can significantly reduce the time delay of data interaction between the virtual and real objects. It can effectively improve the real-time and production flexibility of dynamic and complex tasks such as emergency insertion and task rework. The ability of real-time data interaction and synchronous real-time mapping between physical entities and virtual entities in dynamic scenes such as production line reconstruction and customized production is improved.

show abstract

A systematic literature review on the Digital Twin of the factory in the context of the product and factory lifecycle

Cited by 3 publications

References 30 publications

Towards the digital factory twin – design guide for creating a 3D factory model

Towards the digital factory twin – design guide for creating a 3D factory model

Interoperability of heterogeneous Systems of Systems: from requirements to a reference architecture

Research on data mapping and fusion method of ship production workshop based on digital twins

Contact Info

Product

Resources

About