A study on tribological behaviour of tin-based bearing material in dry sliding

Zeren, Adalet; Feyzullahoğlu, Erol; Zeren, Muzaffer

doi:10.1016/j.matdes.2005.05.016

Cited by 70 publications

(35 citation statements)

References 7 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…6, the Cu 6 Sn 5 intermetallics are distributed in the Sn matrix and have characteristic large star shapes that can be easily identified [5]. The SbSn intermetallics are small white precipitates, dispersed in the solid solution [16]. Fig.…”

Section: Results Of the Experimentsmentioning

confidence: 99%

See 1 more Smart Citation

Embeddability behaviour of tin-based bearing material in dry sliding

Zeren

2007

Materials & Design

View full text Add to dashboard Cite

Section: Results Of the Experimentsmentioning

confidence: 99%

“…The chemical analysis of bearing material is given in Table 3. Hardness of specimen is represented in Table 4 [16].…”

Section: Materials and Experimental Conditionsmentioning

confidence: 99%

Embeddability behaviour of tin-based bearing material in dry sliding

Zeren

2007

Materials & Design

View full text Add to dashboard Cite

“…It is known that alloying of copper with tin enhances the operational properties by improving the embeddability, conformability and resistance to seizure (Zeren at al. [16]; Zeren [17]; Goudarzi et al [18]; Gebretsadik et al [19].…”

Section: Materials Researchedmentioning

confidence: 99%

On Some Mechanical Properties and Wear Behavior of Sintered Bronze Based Composites Reinforced with Some Aluminides Microadditives

Feldshtein

Kiełek

et al. 2017

International Journal of Applied Mechanics and Engineering

View full text Add to dashboard Cite

In the paper, the changes in some mechanical properties and wear behavior of CuSn10 sintered bronze and MMCs based on this bronze reinforced with composite ultrafine aluminide powders FeAl/15 % Al 2 O 3 , NiAl/15 % Al 2 O 3 and Ti-46Al-8Cr are described. It was observed that the presence of aluminides in the MMCs leads to an increase in the hardness, but the flexural strength may increase or decrease depending on the type of aluminide. The presence of aluminides in the MMC reduces the wear rate considerably. It is decreased in the direction of FeAl/15 % Al 2 O 3  NiAl/15 % Al 2 O 3  Ti-46Al-8Cr aluminides and for the best MMC composition the advantage is about 20 times. In the MMCs wear process, micro-craters are formed on the contact surface and it is the principal reason of a decrease in the wear rate.

show abstract

“…However, lead is widely perceived to have an inherent toxicity that causes deleterious and cumulative toxic effects on the environment [15][16][17][18][19][20]. In order to meet the requirements of future possible applications, it is important to improve the existing and to develop new lead free materials with enhanced tribological properties [21].…”

Section: Introductionmentioning

confidence: 99%

Effect of nanosilica additive particles on both friction and wear performance of mild steel/CuSn/SnBi multimaterial system

Ait-Sadi

Hemmouche

Hattali

et al. 2015

Tribology International

View full text Add to dashboard Cite

is an open access repository that collects the work of Arts et Métiers ParisTech researchers and makes it freely available over the web where possible. This paper presents an experimental study of the tribological behaviour of a multimaterial system using conventional powder metallurgy process with SiO 2 nanoparticles. Four configurations were studied with and without SiO 2 . The tribological properties of the sintered materials were analysed by wear experiments at lubricated conditions on a ball disc wear test rig. The results are compared with those of conventional material for journal bearing. These show less variation of the friction coefficient and less wear rate for the materials with SiO 2 compared to the ones without SiO 2 and to those of the reference material. The dominant wear mechanism is adhesive wear, accompanied by mild abrasive wear.

show abstract

A study on tribological behaviour of tin-based bearing material in dry sliding

Cited by 70 publications

References 7 publications

Embeddability behaviour of tin-based bearing material in dry sliding

Embeddability behaviour of tin-based bearing material in dry sliding

On Some Mechanical Properties and Wear Behavior of Sintered Bronze Based Composites Reinforced with Some Aluminides Microadditives

Effect of nanosilica additive particles on both friction and wear performance of mild steel/CuSn/SnBi multimaterial system

Contact Info

Product

Resources

About