A Preliminary Result of Air Quality Identification and Analysis of Pm10 and PM2.5 in Steel  Industrial Area, Cilegon, Banten

Setiawati, Ira; Ermawati, Rahyani; Kang, Kitai; Chang, In-Soo; Hong, Ki‐Hwan; Ervina, Ervina; Ariani, Auliyah; Fauzi, Ilham; Syah, Indra Lukman; Sefriana, Fita; Sari, Yesi Komala

doi:10.21771/jrtppi.2019.v10.no1.p22-28

Cited by 6 publications

(2 citation statements)

References 8 publications

(10 reference statements)

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Moreover, there is also transportation activities for factory supporting goods, which produced dust from the traffic that could be one source of pollution. In a previous study, the same steel industry produced the highest PM2.5 concentrations, namely141.96 μg/m 3 at area of billet post [5]. Based on previous and this study, the PM2.5 concentrations were obtained more by reduction process and slab steel process than other activities in the steel industry.…”

Section: Particle Concentrationsupporting

confidence: 58%

Physicochemical properties of particulate matter (PM2.5) from the steel industry in Indonesia

Ermawati¹,

Setiawati²,

Irwinanita³

et al. 2022

IOP Conf. Ser.: Earth Environ. Sci.

View full text Add to dashboard Cite

Particulate matter (PM) as one of the pollutants in the atmosphere needs to be studied. PM has physical and chemical characteristics and is called physicochemical properties. These properties vary depending on the source of the PM. PM samplers are used for air sampling to characterize some fine particles (PM2.5). The PM2.5 samples have collected from four sampling sites in the steel industry in Cilegon, Indonesia. The sampling sites are the main gate, the hot strip mill, the billet post, and the hot blast plant. The sampling period was four months. The physicochemical properties analysed are morphology, elements content, heavy metals, and particle size. The instruments used to analyse were Scanning Electron Microscopy (SEM) and Energy Dispersive Spectrometry (EDS), Inductively Coupled Plasma Atomic Emission Spectroscopy (ICP-AES), and Particle Size Analyzer (PSA). The morphology of PM2.5 detected varied, but the elements and the most elements found were F and C particles. The metals concentration was below the Indonesia Regulation. While the average particle size analysed was below 2,500 nm. The physicochemical properties of PM2.5 are affected by the type of production process in the industry.

show abstract

Section: Particle Concentrationsupporting

confidence: 58%

Physicochemical properties of particulate matter (PM2.5) from the steel industry in Indonesia

Ermawati¹,

Setiawati²,

Irwinanita³

et al. 2022

IOP Conf. Ser.: Earth Environ. Sci.

View full text Add to dashboard Cite

show abstract

“…Motor vehicle exhaust emissions become one of the contributors to air pollution, especially on the highway. Regular and periodic air quality monitoring must be done in order to identify and control the impact of air pollution in a place, especially the direct impact on the organisms [6]. Frequent monitoring and measuring the motor vehicle exhaust emissions regularly is an obligation for each vehicle owner and the government; hence, exhaust gas emissions remain in clean air.…”

Section: Introductionmentioning

confidence: 99%

A Portable Device of Air Pollution Measurement Due to Highway Exhaust Emissions Using LabVIEW Programming

Andrizal

Lifwarda

Yudanur

et al. 2021

JOIV : Int. J. Inform. Visualization

View full text Add to dashboard Cite

A multisensory gas device integrated with myRIO module to measure air pollution has been established. This device is programmed using the LabVIEW programming language and can measure CO2, CO, NOX, and HC pollution on roads due to motor vehicle exhaust emissions. The device and the display system are made separately using wireless network communication to make this tool portable. Exhaust Gas Analyzer (EGA) was chosen for device calibration, obtaining 3.62% on the average error after performing 30 tests. The tests for measuring CO, CO2, NOX, and HC gas levels were conducted in several locations in Padang City and performed in the morning, afternoon, and evening. The result showed that the system properly measured CO2, CO, NOX and HC pollution in parks and highways in real-time in parts per million (ppm). It also displayed varied gas measurement results in terms of time and test location with a range of CO gas values at 0.034 – 0.15 ppm, CO2 151.3 – 815.2 ppm, NOX 0.0001 – 0.004 ppm, and HC 0.04 – 0.65 ppm. In addition, the system could perform well in providing warnings by automatically activating the air indicator alert at several measurement places when the gas content on one of the gas elements and compounds at a particular location has exceeded the threshold for the clean air category. Thus, this device can be used as initial research to build a real-time air pollution measurement system using the Internet of Things (IoT).

show abstract

Six-week inhalation of lead oxide nanoparticles in mice affects antioxidant defense, immune response, kidneys, intestine and bones

Tulinská

Krivošíková

Líšková

et al. 2022

Environ. Sci.: Nano

View full text Add to dashboard Cite

show abstract

A Preliminary Result of Air Quality Identification and Analysis of Pm10 and PM2.5 in Steel Industrial Area, Cilegon, Banten

Cited by 6 publications

References 8 publications

Physicochemical properties of particulate matter (PM2.5) from the steel industry in Indonesia

Physicochemical properties of particulate matter (PM2.5) from the steel industry in Indonesia

A Portable Device of Air Pollution Measurement Due to Highway Exhaust Emissions Using LabVIEW Programming

Six-week inhalation of lead oxide nanoparticles in mice affects antioxidant defense, immune response, kidneys, intestine and bones

Contact Info

Product

Resources

About