A novel superhydrophobic bulk material

Zhu, Xiaotao; Zhang, Zhaozhu; Ren, Guina; Yang, Jin; Wang, Kun; Xu, Xiaodong; Men, Xuehu; Zhou, Xiaoyan

doi:10.1039/c2jm33769j

Cited by 99 publications

(57 citation statements)

References 28 publications

(30 reference statements)

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…The total downward abradant pressure was maintained at 20.5 kPa, a value relatively high compared to most of the studies that perform such durability tests on superhydrophobic coatings [16,55,56]. In Fig.…”

Section: Resultsmentioning

confidence: 99%

Analysis of wear abrasion resistance of superhydrophobic acrylonitrile butadiene styrene rubber (ABS) nanocomposites

Milionis

Languasco

Loth

et al. 2015

Chemical Engineering Journal

View full text Add to dashboard Cite

Please cite this article as: A. Milionis, J. Languasco, E. Loth, I.S. Bayer, Analysis of wear abrasion resistance of superhydrophobic acrylonitrile butadiene styrene rubber (ABS) nanocomposites, Chemical Engineering Journal (2015), doi: http://dx.ABSTRACT Acrylonitrile butadiene styrene rubber (ABS) superhydrophobic nanocomposites containing various concentrations of hydrophobic silica nanoparticles were obtained by solution processing and spray coating on aluminum surfaces. Wear abrasion resistance measurements were conducted on the superhydrophobic nanocomposites as function of silica nanoparticle concentration. A remarkable increase in coating wear abrasion resistance (1700 linear abrasion cycles under 20.5 kPa) was measured when the nanocomposite coatings were fortified with a synthetic rubber resin adhesive Plasti Dip™. Detailed wetting measurements before and during abrasion cycles were performed. Changes in surface microtexture were monitored with scanning electron microscopy (SEM) as well as confocal microscopy for surface roughness changes. Wear abrasion of sufficiently thick coatings indicated that there was wear similarity (maintenance of hierarchical texture) throughout the coating thickness during cyclic abrasion. Thermal resistance of the coatings was improved by applying a thin primer layer containing multi-walled carbon nanotubes dispersed in a fluoracrylic polymer solution (Capstone ST-110). The superhydrophobicity of the coatings did not degrade until 420 o C. Simplicity of the process and commercial availability of the materials in large scale can open many practical applications of this coating material system in which water-repellent, wear abrasion resistance is needed particularly for metal surfaces.2

show abstract

Section: Resultsmentioning

confidence: 99%

Analysis of wear abrasion resistance of superhydrophobic acrylonitrile butadiene styrene rubber (ABS) nanocomposites

Milionis

Languasco

Loth

et al. 2015

Chemical Engineering Journal

View full text Add to dashboard Cite

show abstract

“…The surface of a PTFE plate has a static water CA of ∼108 • , and a SA >90 • , indicating water adhesion to the PTFE surface [16,17]. Much study has been devoted to the use of the PTFE surface to achieve superhydrophobicity [17][18][19][20][21][22][23][24][25][26][27][28][29][30][31][32][33][34][35], including plasma modification [18][19][20], thin film deposition [21,22], cold pressing and sintering [23], sandpapering [24], filter paper templating [25], hot embossing [26], PTFE-polymer phase separation [27][28][29][30], the formation of a PTFE-carbon nanotube composite plate [31], electrospray formation [32], axially stretching porous films [33], RF sputter deposition onto porous Al surfaces [34], and a two-step process with plasma etching and a nanoparticle assembly template to create controllable surface roughness [35]. Based on these studies, the key preparation requirement appears to be the development of a micro-and nanostructured surface.…”

Section: Introductionmentioning

confidence: 99%

Durable superhydrophobic PTFE films through the introduction of micro- and nanostructured pores

Zhang¹,

Ge²,

Yang³

et al. 2015

Applied Surface Science

View full text Add to dashboard Cite

“…It is found that the chemical composition and geometrical microstructure are two main factors that contribute to those unique properties. [4d,5]…”

Section: Methodsmentioning

confidence: 99%

A Facile Approach for Fabricating Dual‐Function Membrane: Simultaneously Removing Oil from Water and Adsorbing Water‐Soluble Proteins

Zhang

Cao

Liu

et al. 2016

Adv Materials Inter

View full text Add to dashboard Cite

A novel dual‐function membrane is developed that can simultaneously remove oil from water and adsorb water‐soluble proteins by combining mussel‐inspired chemistry and 1‐(3‐Dimethylaminopropyl)‐3‐ethylcarbodiimide hydrochloride/N‐Hydroxysuccinimide (EDC/NHS) activated amide reaction (EDC/NHS coupling reaction). This study provides a new prospect to introduce multiple molecules on the polydopamine/polyethylenepolyamine film to achieve various functional oil/water separation materials.

show abstract

A novel superhydrophobic bulk material

Cited by 99 publications

References 28 publications

Analysis of wear abrasion resistance of superhydrophobic acrylonitrile butadiene styrene rubber (ABS) nanocomposites

Analysis of wear abrasion resistance of superhydrophobic acrylonitrile butadiene styrene rubber (ABS) nanocomposites

Durable superhydrophobic PTFE films through the introduction of micro- and nanostructured pores

A Facile Approach for Fabricating Dual‐Function Membrane: Simultaneously Removing Oil from Water and Adsorbing Water‐Soluble Proteins

Contact Info

Product

Resources

About