A novel EBG structure with super-wideband suppression of simultaneous switching noise in high speed circuits

Tripathi, Jai Narayan; Mukherjee, Jayanta; Apte, P. R.; Nagpal, Raj Kumar; Chhabra, Nitin Kumar; Malik, Rakesh

doi:10.1109/epeps.2013.6703509

Cited by 5 publications

(3 citation statements)

References 11 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Firstly, the circuit generates a reference current through the resistor R 1 . From [33], it is shown that the output current can be expressed by Equation (39).…”

Section: Figure 35 Self-biasing V Th Reference Circuit With Start-up ...mentioning

confidence: 99%

“…However, great care must be taken to choose the location of the split plane since this can lead to return current discontinuities [5]. As discussed previously, The most common configuration is uniplanar EBGs, which have been shown to achieve greater than 50dB of isolation, as shown in [21] and [38,39]. In [35], a design is presented that has partial placement of EBG cells placed near only noise sources and noise sensitive components.…”

Section: Figure 53 Effective Frequency Range Of Several Noise Isolati...mentioning

confidence: 99%

See 1 more Smart Citation

Managing signal and power integrity using power transmission lines and alternative signaling schemes

Telikepalli

Kim

Park

et al. 2013

2013 IEEE 4th Latin American Symposium on Circuits and Systems (LASCAS)

View full text Add to dashboard Cite

Dedicated to my parents and grandparents iv Swaminathan for his guidance and support. I took Professor Swaminathan's Microwave Design class in 2010 and was so interested in the material that I decided to join his research group. I am grateful for his valuable advice and insight and for giving me the opportunity to work on cutting edge research. I would also like to extend my thanks to Professor David Keezer for helping me throughout the years, especially when conducting lab measurements. Also, I would like to extend my sincere thanks to my dissertation committee members, Professors Saibal Mukhopadhyay, Professor Raychowdhury, and Professor Sitaraman for their time and their valuable comments regarding my research. I would also like to express my sincere gratitude to my lab mates at the Mixed Signal Design group. I would like to thank Dr. Junki Min and Dr. Sang-Min Han for their valuable insight and discussions. I have been very fortunate to have worked alongside incredibly intelligent colleagues who have helped me along the way, many of whom I have seen graduate -

show abstract

“…Firstly, the circuit generates a reference current through the resistor R 1 . From [33], it is shown that the output current can be expressed by Equation (39).…”

Section: Figure 35 Self-biasing V Th Reference Circuit With Start-up ...mentioning

confidence: 99%

Section: Figure 53 Effective Frequency Range Of Several Noise Isolati...mentioning

confidence: 99%

Managing signal and power integrity using power transmission lines and alternative signaling schemes

Telikepalli

Kim

Park

et al. 2013

2013 IEEE 4th Latin American Symposium on Circuits and Systems (LASCAS)

View full text Add to dashboard Cite

show abstract

“…However, the notched bandwidth is very narrow. Moreover, the EBG structure has been used in microstrip antennas for surface wave suppression [18], [19], gain enhancement [20], noise suppression [21], [22], and mutual coupling reduction [23].…”

Section: Introductionmentioning

confidence: 99%

Wideband and dual-band antennas with band-notched using electromagnetic band-gap structure

Nasidi¹,

Bello²

2022

Nig. J. Tech.

View full text Add to dashboard Cite

This paper presents a single-element microstrip spade-shaped patch antennas with a partial ground plane, integrated with an electromagnetic band-gap (EBG) structure, and fed with a microstrip feedline to achieve wideband, dual-band and band-notched characteristic. Two similar mushroom-like EBG structures built into the wideband antenna were used to suppress a specific band, resulting in dual-band. The wide-band antenna achieved a broad bandwidth of 9GHz from 5-14GHz, with a maximum gain of 6.8dBi. Based on the simulation and measured results, the wide-band antenna offers 89% fractional bandwidth for a voltage standing wave ratio less than 2 (VSWR < 2). The EBG provides a band-notch with a bandwidth 3GHz from 8-11GHz, leaving dual-band with bandwidths of 2GHz and 1.5GHz centred at 7GHz and 11GHz, respectively. Surface current distribution and parametric studies were conducted to better understand the behaviour and influence of the EBG parameters. The simulation results were validated through experimental measurement, and both agreed well. The antennas could be used for 5G wireless communication and filtering.

show abstract

A novel EBG power plane structure for suppressing SSN in high speed systems

Tripathi

Mukherjee

Apte

et al. 2013

2013 IEEE Electrical Design of Advanced Packaging Systems Symposium (EDAPS)

View full text Add to dashboard Cite

A novel EBG structure with super-wideband suppression of simultaneous switching noise in high speed circuits

Cited by 5 publications

References 11 publications

Managing signal and power integrity using power transmission lines and alternative signaling schemes

Managing signal and power integrity using power transmission lines and alternative signaling schemes

Wideband and dual-band antennas with band-notched using electromagnetic band-gap structure

A novel EBG power plane structure for suppressing SSN in high speed systems

Contact Info

Product

Resources

About