A New Study on Tribological Performance of Cissus Quadrangularis Stem Fiber/Epoxy with Red Mud Filler Composite

Jenish, I.; Gandhi, V. C. Sathish; Raj, R. Edwin; Basavarajappa, S.; Suyambulingam, Indran; Divya, D.; Kumaravelan, R.

doi:10.1080/15440478.2020.1848709

Cited by 29 publications

(13 citation statements)

References 31 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…e thermal and tribological behaviour of the CQSF/Epoxy have been identified as good as compared to other composite materials [9]. It indicates that the thinner the fibers in the composite, the poorer the mechanical qualities.…”

Section: Introductionmentioning

confidence: 91%

“…While these approaches improved matrix ber bonding, enhancing the roughness of the surface, and the mechanical behavior (tensile, exural, and impact strength). Even though chemical treatment enhances the matrix ber bonding, it causes bers to fracture rather than pull out when subjected to mechanical stress [9][10][11]. In the meantime, the hybrid composite of chemically treated and untreated sisal ber-reinforced polylactic acid showed superior quality than the other composition [12].…”

Section: Introductionmentioning

confidence: 95%

See 1 more Smart Citation

Experimental Studies on Mechanical and Thermal Properties of Polyester Hybrid Composites Reinforced with Sansevieria Trifasciata Fibers

Premkumar

Kumar

Maniraj

et al. 2022

Advances in Materials Science and Engineering

Self Cite

View full text Add to dashboard Cite

In the recent decades, natural fiber reinforced composite (NFRC) plays a vital role in most of the engineering applications including automobile and structural. The demand for novel natural fiber increasing steeply in recent times. Current research work aimed to develop hybrid sansevieria trifasciata fiber (HSTF)/polyester composite, and researchers combined untreated sansevieria trifasciata fibers (USTFs) with NaOH treated sisal fibers (NSTFs) and combined them with a polyester matrix. The reinforced effect of HSTFs was shown to be superior to that of NSTFs. It has the tensile strength of 48.47 MPa, the flexural strength of 69.17 MPa, and the impact strength of 16.34 kJ/m2. The thermal behaviour of the composite increased because of chemical treatment and hybrid composition. Polyester/HSTFs show superior mechanical properties compared to other developed samples.

show abstract

Section: Introductionmentioning

confidence: 91%

Section: Introductionmentioning

confidence: 95%

Experimental Studies on Mechanical and Thermal Properties of Polyester Hybrid Composites Reinforced with Sansevieria Trifasciata Fibers

Premkumar

Kumar

Maniraj

et al. 2022

Advances in Materials Science and Engineering

Self Cite

View full text Add to dashboard Cite

show abstract

“…[ 5 ] In this relation, “y” specifies the standardized weight ( w t / w i ), “ R ” stands for the universal gas constant (8.314 KJ/ mol), “ K ” represents the reaction constant, and “ T ” embodies the temperature at a specific time in Kelvin. [ 62 ]

ε = \ln [\ln [\frac{1}{y}]] = - (\frac{E}{R}) [(\frac{1}{T}) + K]

…”

Section: Methodsmentioning

confidence: 99%

Comprehensive characterization of Echinochloa frumentacea leaf fiber as a novel reinforcement for composite applications

Rathinavelu

Paramathma

2022

Polymer Composites

View full text Add to dashboard Cite

The promising characteristic features of some natural plant fibers identified has driven many scientists/researchers to seek more plant fibers with good mechanical, thermal, tensile and surface properties. Plant fibers with such characteristics along with their renewable, degradable, eco‐friendly, cost‐effective nature could make them a probable competitor against synthetic ones, in many aspects. Since identification of novel plant fibers with superior quality is necessary at the moment in order to reduce the harmful effects of synthetic materials. Since the current study recognized a novel natural plant fiber from Echinochloa frumentacea and analyzed its efficiency for composite fabrication through various characterization practices. It was found from the physico‐chemical investigation that the fiber encloses with good crystallinity index (35.87%), cellulose content (60.31%) and relatively low density (896 ± 32.14 kg/m3). In fact, EFLF's has admirable thermal stability (330°C) and tensile strength (204.32 ± 14.25 MPa) designated its suitability for temperature varying environments. Conversely, the proposed fiber ensures good fiber‐matrix adhesion in spite of good surface roughness and decreased microfibrillar angle (9.27 ± 0.31°), noted by surface analysis. Hence, the current study recommends further utilization of EFLF as a reinforcing material with high specific qualities and low environmental effect, for composite manufacturing.

show abstract

“…The criteria were measured using an X'Pert Pro diffractometer. [5,14,28] During the examination, monochromatic X-rays (CuKα 1.5406 Å) were used and scanning was done at a rate of 10 -80 and speed of 1 per minute at a voltage of 40 kV. The resultant peaks were recorded, which were further used to study the crystalline parameters.…”

Section: X-ray Diffraction Assessmentmentioning

confidence: 99%

Suitability characterization of novel cellulosic plant fiber from Ficus benjamina L. aerial root for a potential polymeric composite reinforcement

Mohan¹,

Devasahayam²,

Suyambulingam

et al. 2022

Polymer Composites

View full text Add to dashboard Cite

The demand of plant fibers is increasing day by day due to the worldwide acceptance of natural plant fibers for various applications in a variety of sectors. However, the identification of suitable plant fibers with superior properties is the need of the hour in the context of developing more eco-friendly, renewable, cost-effective, and fiber-based materials. This study was designed with the intention of identifying suitability of Ficus benjamina L. aerial root fiber (FBRF) as a potential reinforcement for composite structures. The fundamental physicochemical, mechanical, thermal, and morphological features were investigated to explore the potentiality of FBRF. This study was advantageous in finding the occurrence of fiber in aerial root, fiber position, and characteristics of fibrous cells. The density analysis proved that the fiber possessed a relatively low density (1175 ± 22.14 kg/m 3 ), which shows its lightweight applicability. High cellulose content (64.48%) and crystallinity index (55.17%) observed for tested fibers in turn enhanced the thermal and mechanical behavior of the fiber. The tensile strength of 292.66 ± 12.32 MPa and thermal stability of 330 C were worthy for considering it for high-temperature processing and applications. The investigation of surface properties revealed that FBRF partake good surface roughness, which offers good fiber-matrix interfacial bonding. Hence, this study endorses further use of FBRF as a good reinforcement for composite manufacturing.

show abstract

A New Study on Tribological Performance of Cissus Quadrangularis Stem Fiber/Epoxy with Red Mud Filler Composite

Cited by 29 publications

References 31 publications

Experimental Studies on Mechanical and Thermal Properties of Polyester Hybrid Composites Reinforced with Sansevieria Trifasciata Fibers

Experimental Studies on Mechanical and Thermal Properties of Polyester Hybrid Composites Reinforced with Sansevieria Trifasciata Fibers

Comprehensive characterization of Echinochloa frumentacea leaf fiber as a novel reinforcement for composite applications

Suitability characterization of novel cellulosic plant fiber from Ficus benjamina L. aerial root for a potential polymeric composite reinforcement

Contact Info

Product

Resources

About