A design method of capacitor arrays for high-resolution SAR ADCs

Wu, Yuqing; Shen, Jizhong; Liang, Jun; Yao, Maoqun

doi:10.1108/cw-09-2019-0124

Cited by 4 publications

(2 citation statements)

References 18 publications

(20 reference statements)

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Meanwhile, to decrease the die size, cost, and the threshold voltage, the MIM (metal-isolated-metal) capacitor DAC array is replaced by a MOS capacitor [29]. Also, a modifed two-stage dual split CDAC array technique is used to avoid the mismatch ofset and reduce the capacitor array size [31][32][33][34]. Tis structure may be divided into three stages: subarray capacitor, the MSB, MLSB and LSB as shown in Figure 11.…”

Section: Capacitive Dac Array (Cdac)mentioning

confidence: 99%

Successive Approximation Register Analog-to-Digital Converter (SAR ADC) for Biomedical Applications

Arafa

Ellaithy

Zekry

et al. 2023

Active and Passive Electronic Components

View full text Add to dashboard Cite

This study presents a survey of the most promising reported SAR ADC designs for biomedical applications, stressing advantages, disadvantages, and limitations, and concludes with a quantitative comparison. Recent progress in the development of a single SAR ADC architecture is reviewed. In wearable and biosensor systems, a very small amount of total power must be devoured by portable batteries or energy-harvesting circuits in order to function correctly. During the past decade, implementation of the high energy efficiency of SAR ADC has become the most necessary. So, several different implementation schemes for the main components of the SAR ADC have been proposed. In this review study, the various circuit architectures have been explained, beginning with the sample and hold (S/H) switching circuits, the dynamic comparator, the internal digital-to-analog converter (DAC), and the SAR control logic. In order to achieve low power consumption, numerous different configurations of dynamic comparator circuits are revealed. At the end of this overview, the evolutions of DAC architecture in distinct biomedical applications today can make a tradeoff between resolution, speed, and linearity, which represent the challenges of a single SAR ADC. For high resolution, the dual split capacitive DAC (CDAC) array technique and hybrid capacitor technique can be used. Also, for ultralow power consumption, various voltage switching schemes are achieved to reduce the number of switches. These schemes can save switching energy and reduce capacitor array area with high linearity. Additionally, to increase the speed of the conversion process, a prediction-based ADC design is employed. Therefore, SAR ADC is considered the ideal solution for biomedical applications.

show abstract

Section: Capacitive Dac Array (Cdac)mentioning

confidence: 99%

Successive Approximation Register Analog-to-Digital Converter (SAR ADC) for Biomedical Applications

Arafa

Ellaithy

Zekry

et al. 2023

Active and Passive Electronic Components

View full text Add to dashboard Cite

show abstract

“…Further, Leakage current and kickback noise in the comparator block is required to be focused upon to improve linearity of the device [7]. Also, DAC consumes power during switching of capacitors between Vref and ground in the switching process of preset-measure-reset in SAR logic [8]. Reduction of switching energy per conversion cycle in designed DAC is one area of importance for the researchers working in mixed signal domain of ADC's implementation.…”

Section: Introductionmentioning

confidence: 99%

Design of 8 -bit low power SAR ADC in 45 nm for biomedical implants

Tyagi,

Mittal,

Kumar

2023

Phys. Scr.

View full text Add to dashboard Cite

The utilisation of low power SAR (Successive Approximation Register) Analog-to-Digital Converters holds significant importance in the domain of bio-medical signal acquisition. The present study showcases the utilisation of an 8-bit CMOS SAR-ADC for integration into the analog front end of bio-signal acquisition. The focus of this technology pertains to the monitoring of implanted bio-signal devices, with a specific emphasis on ECG/EEG signals. A capacitive digital-to-analog converter (DAC) is suggested as a means to attain power consumption in the microwatt range. This approach enables comparisons to be made without any energy consumption, leading to a substantial enhancement in energy efficiency. Furthermore, a comprehensive theoretical examination of comparator offset voltages has been conducted to enhance the offset performance of the comparator operating at low supply voltage. The analysis indicates that optimization of the comparator is achieved solely through the adjustment of transistor sizes, without the implementation of any specific offset cancellation techniques. Simulations indicate that the optimization of the offset voltage to approximately 5 mV occurs when there is variation in the common-mode input voltage at a 1 V supply. The proposed Analog-to-Digital Converter (ADC) layout has been successfully executed utilizing the 45 nm Complementary Metal-Oxide-Semiconductor (CMOS) technology. The Analog-to-Digital Converter (ADC) attains a Spurious-Free Dynamic Range (SFDR) of 64.02 dB and consumes 1.9 μW of power at a sampling rate of 1.1 MHz and a supply voltage of 1 V.

show abstract