A CD probe with a tailored cantilever for 3D-AFM measurement

Abstract

A critical dimensional (CD) probe, such as a boot shaped probe, is widely used for measuring the sidewall profiles of nanostructures in atomic force microscopy (AFM). However, conventional CD probes usually have high spring constants that restrict their ability to operate in critical dimension scanning modes. Furthermore, the flexure spring constant of the tip is much smaller than the torsion spring constant of the cantilever, which probably makes the sidewall measurement unstable. Here, we proposed a method of tailoring the probe where the cantilever was trimmed to reduce the spring constant. The simulation results, using a finite element method (FEM), illustrated that both the flexure and torsion spring constants decreased nearly ten times. Meanwhile, the torsional resonant frequency decreased to below 1 MHz, which could benefit the torsional oscillation scanning. By using a focused ion beam (FIB), a CD probe with a rectangular cantilever was reprocessed. It was mounted to a home-built three-dimensional AFM system (3D-AFM), and had the flexure and torsion sensitivities precisely calibrated. The ratio of the flexure sensitivity to torsion sensitivity showed good accordance with the simulation results. Additionally, a grating standard sample was measured using the tailored probe under a modified step-in scanning mode, and the error due to torsional deformation of the tip was compensated. The measurement results demonstrated the validity of the tailored CD probe in 3D metrology.

Nanoscale physical parameters of source rocks identified by atomic force microscopy: A review

“…AFM can be applied in materials science (morphology, electrical, magnetic and mechanical properties) (Vlassov et al, 2018; Wang et al, 2021), physics (many physical properties of materials are detected, including those in nanophysics, mesophysics and microscopic physics) (Chen & Xu, 2020; Dufrêne et al, 2021; Zhu, Tan, & Hong, 2021), chemistry (in situ detection for chemical reactions in a controlled environment, surface chemical reactions and changes at the atomic level) (Abarghani et al, 2020; Labidi et al, 2017; McDonald et al, 2020; Silbernagl et al, 2021), biology (movement and morphology of DNA, RNA, protein and cells, in situ high‐resolution liquid imaging of interactions between membranes and viruses, protein folding molecular forces, biological macromolecules, and cell surface antigens (Amarouch et al, 2018; Pi & Cai, 2019), and surface treatments for cutting DNA, microtubules, and other small fibres) (Bitler et al, 2018; Chen & Xu, 2020; Chiorcea‐Paquim et al, 2018; Hubert et al, 2019; Main et al, 2021; Schön, 2018), microelectronics (large‐scale integrated circuit detection, local electrical properties of integrated circuit (IC), storage and reading of ultrahigh density optical/magnetic information) (Yuan et al, 2017, 2020; Zhang et al, 2018), and medicine (a powerful tool for mesoscopic and nanoscopic research on biological cells, combining an inverted biological microscope, fluorescence microscope, fluorescence energy resonance transfer microscope and confocal microscope, which are widely used in medicine, pharmacology, immunology, therapy, nanoscopic research, etc.) (Chen & Xu, 2020; Silbernagl et al, 2021; Yang, 2016; Zhou et al, 2021).…”

Development of a High-Function Fiber Stylus for Microstructure Measurement with Water-Repellent and Antistatic Coatings

“…However, it is extremely difficult to accurately measure microstructures such as micrometer-order small holes and grooves with a high aspect ratio. Various microstructure measurement system based on different principles have been proposed [4][5][6][7][8][9][10][11][12][13][14][15].…”

Three-Dimensional Kelvin Probe Force Microscopy

“…The protruding tip on the vertical cantilever enables the detection of deep grooves and re-entrant structures. Compared with the flared probe usually used for 3D topography scanning, 36 the designed OCP with a sharp tip significantly improves the accuracy of the local CPD measurement. The proposed method contains three specific modes: a bending mode for 2D horizontal surface imaging, a torsion mode for vertical sidewall imaging, and a vector tracking-based 3D scanning mode.…”