Untitled

López, Carmen M.; Machado, Francisco J.; Méndez, Bernardo; Pinto, M.; Sazo, Virginia; Goldwasser, J.; Ramírez, M.M.

doi:10.1023/a:1019107916156

Cited by 11 publications

(2 citation statements)

References 20 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The SSA values lie within the range previously reported for this kind of solids [12,15]. The acid treatment of HBeta caused 60% dealumination (Si/Al molar ratio increases from 15 to 41), retaining more than 90% crystallinity.…”

Section: Resultssupporting

confidence: 88%

See 1 more Smart Citation

n-Pentane Hydroisomerization on Pt Containing HZSM-5, HBEA and SAPO-11

et al. 2008

View full text Add to dashboard Cite

Hydroisomerization of n-pentane over platinum promoted acids zeolites was studied. The effect of structure and acidity of the support was investigated at atmospheric pressure between 250 and 400°C. Pt/HDBEA catalyst showed the best performance at 300°C with high activity and selectivity to isopentane, due to its structure and a proper balance between acid and metallic sites. This catalyst has a high catalytic stability and regeneration under air flow after deactivation by coking, restores its activity and selectivity.

show abstract

Section: Resultssupporting

confidence: 88%

“…The synthesis procedure for SAPO-11 has been reported elsewhere [15]. The gel molar composition was Al 2 O 3 : P 2 O 5 :DPA:0.3SiO 2 :50H 2 O, a final crystallization temperature of 200°C and a crystallization time of 24 h was employed.…”

Section: Preparation and Characterization Of Catalystsmentioning

confidence: 99%

n-Pentane Hydroisomerization on Pt Containing HZSM-5, HBEA and SAPO-11

et al. 2008

View full text Add to dashboard Cite

show abstract

Dry‐gel conversion synthesis of SAPO‐11 molecular sieves and their use in hydroisodewaxing of hydrocracking recycle oil

Song

Yang

Wang

et al. 2016

Asia-Pacific J Chem Eng

View full text Add to dashboard Cite

Silicoaluminophosphate (SAPO‐11) molecular sieves were synthesized by the dry‐gel conversion [i.e. steam‐assisted conversion and vapor‐phase transport (VPT)] method using di‐n‐propylamine as a structure‐directing agent. The influence of the bottom water content, the crystallization time, the drying time and the pH value was investigated. The properties of the as‐synthesized samples were characterized by X‐ray powder diffraction, scanning electron microscopy, N2‐adsorption and NH3‐temperature‐programmed desorption. The results show that the crystallization process of SAPO‐11 was closely related to the pH value and the drying time of the gel; the amount of water in the wet gel plays an important role for SAPO‐11 formation. It can be observed that when the crystal time is within 48 h, and the pH value of the gel is between 0 and 5, the longer the crystal time and the higher the pH value, the higher the crystallinity of the samples. The presence of NH4+ leads to the formation of an amorphous phase in the samples synthesized by the VPT method. Of these two methods, the steam‐assisted conversion method exhibits better Si incorporation into the AlPO4 framework than the VPT method. The results from hydroisodewaxing of hydrocracking recycle oil show that the Pt/SAPO‐11 catalysts synthesized by these methods possess high activity and selectivity of isomerization. The pour point of the lubricating base oils can be lowered to below −15 from 42 °C. Copyright © 2016 Curtin University of Technology and John Wiley & Sons, Ltd.

show abstract