55-TW magnetically insulated transmission-line system: Design, simulations, and performance

Abstract

We describe herein a system of self-magnetically insulated vacuum transmission lines (MITLs) that operated successfully at 20 MA, 3 MV, and 55 TW. The system delivered the electromagnetic-power pulse generated by the Z accelerator to a physics-package load on over 1700 Z shots. The system included four levels that were electrically in parallel. Each level consisted of a water flare, vacuum-insulator stack, vacuum flare, and 1.3-m-radius conical outer MITL. The outputs of the four outer MITLs were connected in parallel by a 7.6-cm-radius 12-post double-post-hole vacuum convolute. The convolute added the currents of the four outer MITLs, and delivered the combined current to a single 6-cm-long inner MITL. The inner MITL delivered the current to the load. The total initial inductance of the stack-MITL system was 11 nH. A 300-element transmission-line-circuit model of the system has been developed using the TL code. The model accounts for the following: (i) impedance and electrical length of each of the 300 circuit elements, (ii) electron emission from MITL-cathode surfaces wherever the electric field has previously exceeded a constant threshold value, (iii) Child-Langmuir electron loss in the MITLs before magnetic insulation is established, (iv) MITL-flow-electron loss after insulation, assuming either collisionless or collisional electron flow, (v) MITL-gap closure, (vi) energy loss to MITL conductors operated at high lineal current densities, (vii) time-dependent self-consistent inductance of an imploding z-pinch load, and (viii) load resistance, which is assumed to be constant. Simulations performed with the TL model demonstrate that the nominal geometric outer-MITL-system impedance that optimizes overall performance is a factor of $3 greater than the convolute-load impedance, which is consistent with an analytic model of an idealized MITL-load system. Power-flow measurements demonstrate that, until peak current, the Z stack-MITL system performed as expected. TL calculations of the peak electromagnetic power at the stack, stack energy, stack voltage, outer-MITL current, and load current, as well as the pinch-implosion time, agree with measurements to within 5%. After peak current, TL calculations and measurements diverge, which appears to be due in part to the idealized pinch model assumed by TL. The results presented suggest that the design of the Z accelerator's stack-MITL system, and the TL model, can serve as starting points for the design of stack-MITL systems of future superpower accelerators.

Simulations of the implosion and stagnation of compact wire arrays

“…1. [11][12][13] Water transmission lines couple to a water/ vacuum insulator stack which drive four vacuum magnetically insulated transmission lines ͑MITL͒ ͑a͒. These lines are coupled together through a double post hole convolute ͑b͒ that connects to a short final transmission line feeding the wire array load region ͑c͒.…”

107-A load-currentB-dot monitor: Simulations, design, and performance

“…The higher impedance of the load during the rising portion of the power pulse resulted in higher voltages in the MITLs and convolute. The higher voltages result in greater current losses between the outer-MITL and inner-MITL B-dot probes [29]. The actual nature of these current losses is the subject of considerable study [4,14,[23][24][25][26][27][28][29] with particular emphasis on the formation of electrode plasmas in the convolute that lead to gap closure.…”

“…The load-current B-dot probes on ZR are located 6 cm from the axis of the load, which is located at the center of the machine. Just upstream of these probes, electrical power that is transported by four radial MITLs is combined by a double-post-hole vacuum convolute [4,14,[20][21][22][23][24][25][26][27][28][29]. The four MITLs located upstream of the convolute are referred to as the outer MITLs.…”

Millimeter-Gap Magnetically Insulated Transmission Line Power Flow Experiments

“…Magnetically insulated transmission lines (MITLs) are commonly used in the final stages of pulsed power systems to transfer power at high voltage and current to the physics-package load. Areas such as the convolute and inner-MITL of the Z-Machine require MA/cm level currents to be transmitted with vacuum gaps of 1 cm or less [1]. Future pulsed power systems, which will deliver greater power to loads, will require MITLs to transfer power at greater power densities.…”