Taguchi's technique in machining of metal matrix composites

Shetty, Raviraj; Pai, Radhika M.; Rao, Shrikanth S.; Nayak, Rajesh

doi:10.1590/s1678-58782009000100003

Cited by 61 publications

(25 citation statements)

References 18 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The performance characteristic of the signal-to-noise ratio (S/N) used in this study is given by Equation (1), low the better, when the characteristic is continuous [10]:…”

Section: Design Of Experimentsmentioning

confidence: 99%

Experimentation on Tool Wear and Surface Roughness in AISI D2 Steel Turning with WC Insert

López-Luiz¹,

Jiménez²,

Hernández³

et al. 2018

MME

View full text Add to dashboard Cite

The Taguchi method, based on an orthogonal arrangement (L 9 , 3 3 ), the variance analysis, the signal-to-noise ratios and the response surface methodology have been used to optimize maximum flank wear (VB max ) and surface roughness (Ra) of the cutting tool when turning a hardened steel AISI D2 (65 HRC) with PVD-TiAlN coated WC insert upon dry environment. By employing regression models; cutting speed, cutting depth and feed rate, which optimize maximum flank wear and surface roughness were validated. Results of relation signal-to-noise ratios, showed that with cutting speed of 200 m/min, cutting depth of 0.2 mm and feed rate of 0.20 mm/rev, Ra is optimized. With cutting speed of 150 m/min, cutting depth of 0.4 mm and feed rate of 0.3 mm/rev, VB max is optimized. Through the variance analysis it was concluded that the depth of cut was the main parameter that affected on the surface roughness; whereas, the feed rate was the most influential parameter on the flank wear. Confirmation test results showed that the Taguchi method was very successful in the optimization of machining parameters for minimum surface roughness and flank wear in the turning of the D2 steel.

show abstract

“…The performance characteristic of the signal-to-noise ratio (S/N) used in this study is given by Equation (1), low the better, when the characteristic is continuous [10]:…”

Section: Design Of Experimentsmentioning

confidence: 99%

Experimentation on Tool Wear and Surface Roughness in AISI D2 Steel Turning with WC Insert

López-Luiz¹,

Jiménez²,

Hernández³

et al. 2018

MME

View full text Add to dashboard Cite

show abstract

“…The last two categories can be used for the optimization in this study and the formulas are given by Eqs. (1) and (2), when the characteristic is continuous [41].…”

Section: Surface Mechanical Propertiesmentioning

confidence: 99%

Ti/TiN/HA coating on Ti–6Al–4V for biomedical applications

Mohseni

Zalnezhad

Bushroa

et al. 2015

Ceramics International

View full text Add to dashboard Cite

“…Two level interactions between the parameters were studied. It was observed form the table that some of the interactions between parameters affect the cutting force but their contribution was very minimum, hence can be neglected [28,29]. Figure 9 shows main effect plot for the SN ratio for cutting force produced during the experiment.…”

Section: Resultsmentioning

confidence: 99%

Analysis of Cutting Force Developed During Turning of SiC Reinforced ZA43 MMC with Ceramic Tool Using Design of Experiments

Marigoudar¹,

Sadashivappa²

2012

Journal for Manufacturing Science &Amp; Production

View full text Add to dashboard Cite

This paper presents a study of cutting forces during turning of ZA43 alloy reinforced with SiC was carried out with SNMG ceramic tools. The fabrication of MMC was done using liquid metallurgy technique. SiC particle size (30 µm, 60 µm and 120 µm) and volume fraction (5%, 10% and 15%) was varied during the fabrication process. The MMC specimen was turned with ceramic tool under dry condition by varying machining parameters. Cutting force measurement was carried out during the experiment and influence of machining conditions and material composition on cutting force was analyzed. The plan of experiment with 243 trials was designed by full factorial method. ANOVA was used to check the significant parameters affecting the cutting force value. The results reveal that increasing depth of cut, particle size and volume fraction cause significant increase in the cutting force where as cutting force decreases with increase in cutting speed.

show abstract

Taguchi's technique in machining of metal matrix composites

Abstract: Taguchi's Technique in Machining of Metal Matrix Composites

Cited by 61 publications

References 18 publications

Experimentation on Tool Wear and Surface Roughness in AISI D2 Steel Turning with WC Insert

Experimentation on Tool Wear and Surface Roughness in AISI D2 Steel Turning with WC Insert

Ti/TiN/HA coating on Ti–6Al–4V for biomedical applications

Analysis of Cutting Force Developed During Turning of SiC Reinforced ZA43 MMC with Ceramic Tool Using Design of Experiments

Contact Info

Product

Resources

About