The performance of dye-sensitized solar and photoelectrochemical cells is strongly dependent on the light absorption and electron transfer events at the semiconductor−small molecule interface. These processes as well as photo/electrochemical stability are dictated not only by the properties of the chromophore and metal oxide but also by the structure of the dye molecule, the number of surface binding groups, and their mode of binding to the surface. In this article, we report the photophysical and electrochemical properties of a series of six phosphonate-derivatized [Ru(bpy) 3 ] 2+ complexes in aqueous solution and bound to ZrO 2 and TiO 2 surfaces. A decrease in injection yield and cross surface electron-transfer rate with increased number of diphosphonated ligands was observed. Additional phosphonate groups for surface binding did impart increased electrochemical and photostability. All complexes exhibit similar back-electron-transfer kinetics, suggesting an electron-transfer process rate-limited by electron transport through the interior of TiO 2 to the interface. With all results considered, the ruthenium polypyridyl derivatives with one or two 4,4′-(PO 3 H 2 ) 2 bpy ligands provide the best balance of electron injection efficiency and stability for application in solar energy conversion devices.

Artificial photosynthesis and the production of solar fuels could be a key element in a future renewable energy economy providing a solution to the energy storage problem in solar energy conversion. We describe a hybrid strategy for solar water splitting based on a dye sensitized photoelectrosynthesis cell. It uses a derivatized, core-shell nanostructured photoanode with the core a high surface area conductive metal oxide film--indium tin oxide or antimony tin oxide--coated with a thin outer shell of TiO 2 formed by atomic layer deposition. A "chromophore-catalyst assembly" 1, [(PO 3 H 2 ) 2 bpy) 2 Ru(4-Mebpy-4-bimpy)Rub(tpy)(OH 2 )] 4+ , which combines both light absorber and water oxidation catalyst in a single molecule, was attached to the TiO 2 shell. Visible photolysis of the resulting core-shell assembly structure with a Pt cathode resulted in water splitting into hydrogen and oxygen with an absorbed photon conversion efficiency of 4.4% at peak photocurrent.P hotosynthesis uses the energy of the sun with water as the reducing agent to drive the reduction of carbon dioxide to carbohydrates with oxygen as a coproduct through a remarkably complex process. At photosystem II, a subsystem imbedded in the thylakoid membrane where O 2 is produced, light absorption, energy migration, electron transfer, proton transfer, and catalysis are all used in multiple stepwise chemical reactions which are carefully orchestrated at the molecular level (1, 2).Photosynthesis solves the problem of energy storage by biomass production but with low solar efficiencies, typically <1%. In artificial photosynthesis with solar fuels production, the goal is similar but the targets are either hydrogen production from water splitting, Eq. 1, or reduction of carbon dioxide to a carbon-based fuel, Eq. 2 (3, 4). Different strategies for solar fuels have evolved (5, 6). In one, direct bandgap excitation of semiconductors creates electron-hole pairs which are then used to drive separate halfreactions for water oxidation (2H 2 O → O 2 + 4H + + 4e − ) and water/proton reduction (2H + + 2e − → H 2 ) (7-9).Here, we report a hybrid strategy for solar water splitting, the dye sensitized photoelectrosynthesis cell (DSPEC). It combines the electron transport properties of semiconductor nanocrystalline thin films with molecular-level reactions (10). In this approach, a chromophore-catalyst molecular assembly acts as both light absorber and catalyst. It is bound to the surface of a "core-shell," nanostructured, transparent conducting oxide film. The core structure consists of a nanoparticle film of either tin-doped indium oxide (nanoITO), or antimony-doped tin oxide (nanoATO), deposited on a fluoride-doped tin oxide (FTO) glass substrate. The shell consists of a conformal TiO 2 nanolayer applied by atomic layer deposition (ALD). The resulting "photoanode," where water oxidation occurs, is connected to a Pt cathode for proton reduction to complete the water splitting cell. A diagram for the photoanode in the DSPEC device is shown in Fig. 1. It illustrates...

The photostability of [Ru(II)(bpy)(2)(4,4'-(PO(3)H(2))(2)bpy)]Cl(2) (bpy = 4,4'-bipyridine) on nanocrystalline TiO(2) and ZrO(2) films was investigated using a standard measurement protocol. Stability was evaluated by monitoring visible light absorbance spectral changes, in real time, during 455 nm photolysis (30 nm fwhm, 475 mW/cm(2)) in a variety of conditions relevant to dye-sensitized solar cells and dye-sensitized photoelectrosynthesis cells. Desorption (k(des)) and photochemical (k(chem)) processes were observed and found to be dependent upon solvent, anion, semiconductor, and presence of oxygen. Both processes are affected by oxygen with k(des) and k(photo) noticeably smaller in argon saturated solution. Desorption was strongly solvent and pH dependent with desorption rates increasing in the order: methanol (MeOH) ≈ acetonitrile (MeCN) < propylene carbonate (PC) < pH 1 ≪ pH 7. Photochemistry occurred in MeOH and PC but not in aqueous, 0.1 M HClO(4) and MeCN. The anion and solvent dependence of k(photo) strongly suggests the photoreaction involves ligand substitution initiated by population of metal centered d-d states. The relative stability of -PO(3)H(2)- versus -COOH-substituted [Ru(II)(bpy)(3)](2+) was also quantitatively established.

Photoelectrochemical (PEC) water oxidation has attracted heightened interest in solar fuel production. It is well accepted that water oxidation on hematite is mediated by surface trapped holes, characterized to be the high valent -Fe═O species. However, the mechanism of the subsequent rate-limiting O-O bond formation step is still a missing piece. Herein we investigate the reaction order of interfacial hole transfer by rate law analysis based on electrochemical impedance spectroscopy (EIS) measurement and probe the reaction intermediates by operando Fourier-transform infrared (FT-IR) spectroscopy. Distinct reaction orders of ∼1 and ∼2 were observed in near-neutral and highly alkaline environments, respectively. The unity rate law in near-neutral pH regions suggests a mechanism of water nucleophilic attack (WNA) to -Fe═O to form the O-O bond. Operando observation of a surface superoxide species that hydrogen bonded to the adjacent hydroxyl group by FT-IR further confirmed this pathway. In highly alkaline regions, coupling of adjacent surface trapped holes (I2M) becomes the dominant mechanism. While both are operable at intermediate pHs, mechanism switch from I2M to WNA induced by local pH decrease was observed at high photocurrent level. Our results highlight the significant impact of surface protonation on O-O bond formation pathways and oxygen evolution kinetics on hematite surfaces.