The elements of transport into and across the scrape-off layer in the poloidal divertor tokamak ASDEX Upgrade are analysed for different operational regimes with emphasis on enhanced confinement regimes with an edge barrier. Utilizing the existing set of edge diagnostics, especially the highresolution multi-pulse edge Thomson scattering system, in combination with long discharge plateaus, radial sweeps and advanced averaging techniques, detailed radial mid-plane profiles of diverted plasmas are obtained. Profiles are smooth across the separatrix, indicating strong radial correlation, and there is no remarkable variation across the second separatrix either. Together with measured input, recycling, pumping and bypass fluxes, a corrected separatrix position is determined and transport characteristics are derived in the different radial zones generally identified in the profile structure. Transport in the steep gradient region inside and across the separatrix shows typical ballooning-type critical electron pressure gradient scaling and, in parallel, even a clear correlation between radial electron density and temperature decay lengths (e.g. η e = d(ln T )/d(ln n) ∼ 2 for type-I ELMy H-modes). These findings indicate the importance of stiff profiles in this region, while diffusion coefficients are secondary parameters, determined essentially by the source distribution. The outer scrape-off layer wing exhibits a more filamentary structure with preferential outward drift especially in high-performance discharges, with formal diffusion coefficients far above the Bohm value in agreement with results on the old ASDEX experiment. A basic mechanism involved there seems to be partial loss of equilibrium and fast curvaturedriven outward acceleration, in principle well known from theory, investigated decades ago in pinch experiments and utilized recently in high-field-side pellet fuelling.
Injection of cryogenic deuterium pellets has been successfully applied in ASDEX Upgrade for external edge localized mode (ELM) frequency control in type-I ELMy H-mode discharge scenarios. A pellet velocity of 560 m s −1 and a size of about 6×10 19 D-atoms was selected for technical reasons, although even lower masses were found sufficient to trigger ELMs. A moderate repetition rate close to 20 Hz was chosen to avoid over-fuelling of the core plasma. Pellet sequences of up to 4 s duration were injected into discharges close to the L-H threshold, intrinsically developing large compound ELMs at a rate of 3 Hz. With pellet injection, these large ELMs were completely replaced by smaller type-I ELMs at the much higher pellet frequency, accompanied by a slight increase of density and even of stored energy. This external ELM control could be repeatedly switched on and off by just interrupting the pellet train. ELMs were triggered in less than 200 µs after pellet arrival at the plasma edge, at which time only a fraction of the pellet has been ablated, forming a rather localized, three-dimensional plasmoid, which drives the edge unstable well before the deposited mass is spread toroidally. The pellet controlled case has also been compared with a discharge at a somewhat lower density, but with otherwise rather similar data, developing spontaneous 20 Hz type-I ELMs. Despite the different trigger mechanisms, the general ELM features turn out to be qualitatively similar, possibly because of the similarity of the two cases in terms of ELM relevant parameters. The scaling with background plasma, heating power, pellet launch parameters, etc over a larger range still remains to be investigated.
Density limit investigations on ASDEX have been performed under a variety of conditions: ohmically heated and neutral injection heated plasmas in H2, D2 and He have been studied in different divertor configurations, after various wall coating procedures, with gas puff and pellet fuelling, and in different confinement regimes with their characteristically different density profiles. A detailed description of the parametric dependence of the density limit, which in all cases is a disruptive limit, is given. This limit is shown to be a limit to the density at the plasma edge. Therefore, the highest densities corresponding to neRqa/Bt>30*1019 m-2.T-1 are obtained with centrally peaked ne profiles. Radiation from the main plasma at the density limit is always significantly below the total input power. The plasma disruption is due to an m=2 instability which for medium and high qa is preceded by one or more minor disruptions. In this range of qa, the disruptive instability is initiated by the occurrence of a Marfe on the high field side as a consequence of strong plasma cooling in this region. The duration of the Marfe increases with increasing distance between the plasma edge and the q=2 surface. After penetrating onto closed flux surfaces the Marfe leads to a current contraction and a subsequent destabilization of the m = 2 mode. In helium plasmas a strongly radiating, poloidally symmetric shell is observed before the density limit instead of a Marfe. An instantaneous destabilization of this mode is observed at low qa. Detailed measurements of plasma edge and divertor parameters close to the density limit indicate the development of a cold, dense divertor plasma before the disruption. Models describing the scrape-off layer and the divertor region predict an upper limit to the edge density at low divertor temperatures according to power balance considerations. Their relations to the experimental findings, especially the low field side cooling, ar
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.