This study aimed at evaluating the microtensile bond strength (MTBS) and fractographic features of dentine-bonded specimens created using universal adhesives applied in etch-and-rinse (ER) or self-etching (SE) mode in combination with modern ion-releasing resin-modified glass-ionomer cement (RMGIC)-based materials after load cycling and artificial saliva aging. Two universal adhesives (FTB: Futurabond M+, VOCO, Germany; SCU: Scotchbond Universal, 3M Oral Care, USA) were used. Composite build-ups were made with conventional nano-filled composite (AURA, SDI, Australia), conventional resin-modified glass ionomer cement (Ionolux VOCO, Germany), or a (RMGIC)-based composite (ACTIVA, Pulpdent, USA). The specimens were divided in three groups and immersed in deionized water for 24 h, load-cycled (350,000 cycles; 3 Hz; 70 N), or load-cycled and cut into matchsticks and finally immersed for 8 months in artificial saliva (AS). The specimens were cut into matchsticks and tested for microtensile bond strength. The results were analyzed statistically using three-way ANOVA and Fisher’s LSD post hoc test (p < 0.05). Fractographic analysis was performed through stereomicroscope and FE-SEM. FTB showed no significant drop in bond strength after aging. Unlike the conventional composite, the two RMGIC-based materials caused no bond strength reduction in SCU after load-cycle aging and after prolonged aging (8 months). The SEM fractographic analysis showed severe degradation, especially with composite applied on dentine bonded with SCU in ER mode; such degradation was less evident with the two GIC-based materials. The dentine-bond longevity may be influenced by the composition rather than the mode of application (ER vs. SE) of the universal adhesives. Moreover, the choice of the restorative material may play an important role on the longevity of the finalrestoration. Indeed, bioactive GIC-based materials may contribute to maintain the bonding performance of simplified universal adhesives over time, especially when these bonding systems are applied in ER mode.
The aim of this study was to perform a 8-year prospective clinical investigation on the survival rate of feldspathic ceramic veneers, as well as analyse the influence of the occlusal splint in patients with parafunctional bruxism. METHODS Three hundred and sixty-four veneers fabricated using conventional feldspathic ceramic were provided in 64 patients. The patient sample included 40 individuals with bruxism. During the follow-up period, the effect of wearing the occlusal splint on the incidence of failure (fracture and/or debonding) in patients with bruxism was also assessed. The survival rate of veneers was determined using the Kaplan-Meier estimator. Statistical significance was set at p < 0.05 with a confidence interval of 95%. RESULTS The occurrence of fracture for the feldspathic veneers tested in this study was 7.7%, while only 1.9% of the total number of veneers debonded. The overall survival rate was 93.7% after 3 years, 91% after 5 years, and 87.1% after 8 years. Patients with bruxism using an occlusal splint showed a survival rate of 89.1% after 7 years, while the survival rate in patients with bruxism using no occlusal splint was 63.9% (p < 0.05). CONCLUSION This study confirmed that feldspathic veneers may represent a suitable clinical solution for indirect aesthetic restorations. Such a treatment may be an option also for those patients affected by bruxism, as long as they regularly wear an occlusal splint. However, patients with bruxism using no occlusal splint may still present a potential high-risk of failure and/or debonding.
Excessive gingival display is an esthetic concern for patients. It is a condition in which an overexposure of the maxillary gingiva (>3mm) is present during smiling. There are different etiologies of a gummy smile, such as vertical maxillary excess, short and hyperactive upper lip, altered passive eruption, anterior dentoalveolar extrusion, or a combination of these causes. The correct diagnosis of all etiologic factors is imperative for its appropriate management. Many techniques have been used to restore the dentogingival relation for the management of gummy smile. Lip repositioning is a conservative surgical technique used to treat excess gingival display. It is a largely unknown treatment modality. This limits lip elevation on smiling and increases lip fullness. This technique was designed to be shorter, less aggressive and to have fewer postoperative complications compared to orthognathic surgery. In the current case series presents three patients who were successfully managed with lip repositioning. The aim of this article is to describe the lip repositioning technique to decrease gummy smile by a simple surgical procedure. Key words:Lip repositioning, gummy smile, smile harmony.
The treatment of severe tetracycline discoloration is a challenge for the dentist. There are several treatment options and one of the most effective is the use of feldspathic veneers. The aim of this clinical case was to carry out the replacement with conventional feldspathic ceramic veneers on a patient with highly stained teeth (grade IV tetracycline) by a minimally invasive approach. Clinical examination revealed gingival retraction, color change of the veneers, ceramic cracked of 1.1 and 1.3 and incisal wear in lower anterior teeth. The decision was to retreat with feldspathic ceramic veneers from 1.6 to 2.6. Premolars and first molars were included because its dark color intensifies the width buccal corridors. Also, the restoration with veneers from 3.3 to 4.3 was considered. Firstly, the veneers were removed and the color was selected by the Vitapan 3D Master guide (Vita Zahnfabrick, Bad Säckingen, Germany). Mock-up was made to evaluate aesthetic, phonetic and functional parameters. Then, teeth were prepared through the mock-up in order to reduce the minimal amount of dental tissue possible. Opaque dentine mass of microhybrid composite (Esthet-X A2O, Dentsply Sirona, Konstanz, Germany) was placed to mask the most intense stains. The definitive impressions were taken with silicone (Aquasil Ultra XLV, Dentsply Sirona, Konstanz, Germany) were taken to fabricate conventional feldsphatic ceramic veneers (Noritake kisai Co, Ltd. Japan) by the parallel stratification masking technique. For cementing, an opaque cement was selected from the try-in tests (Calibra, Dentsply Sirona, Konstanz, Germany) and the composite was silicatized with an air-abrasion device. A favorable and minimally invasive result was achieved to treat grade IV tetracycline stains, surpassing the patient’s aesthetic expectations and functional needs. Key words:Porcelain veneer, tetracycline teeth, minimally invasive, masking, opaque composite.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.