Surgical reconstruction is generally recommended for posterior cruciate ligament (PCL) injuries; however, the use of grafts is still a controversial problem. In this study, a three-dimensional finite element model of the human tibiofemoral joint with articular cartilage layers, menisci, and four main ligaments was constructed to investigate the effects of graft strengths on knee kinematics and in-situ forces of PCL grafts. Nine different graft strengths with stiffness ranging from 0% (PCL rupture) to 200%, in increments of 25%, of an intact PCL’s strength were used to simulate the PCL reconstruction. A 100 N posterior tibial drawer load was applied to the knee joint at full extension. Results revealed that the maximum posterior translation of the PCL rupture model (0% stiffness) was 6.77 mm in the medial compartment, which resulted in tibial internal rotation of about 3.01°. After PCL reconstruction with any graft strength, the laxity of the medial tibial compartment was noticeably improved. Tibial translation and rotation were similar to the intact knee after PCL reconstruction with graft strengths ranging from 75% to 125% of an intact PCL. When the graft’s strength surpassed 150%, the medial tibia moved forward and external tibial rotation greatly increased. The in-situ forces generated in the PCL grafts ranged from 13.15 N to 75.82 N, depending on the stiffness. In conclusion, the strength of PCL grafts have has a noticeable effect on anterior-posterior translation of the medial tibial compartment and its in-situ force. Similar kinematic response may happen in the models when the PCL graft’s strength lies between 75% and 125% of an intact PCL.

Polyethylene particle-induced osteolysis is the primary limitation in the long-term success of total joint replacement with conventional ultra high molecular weight polyethylene (UHMWPE). Highly cross-linked polyethylene (HXLPE) and vitamin E-doped cross-linked polyethylene (VE-HXLPE) have been developed to increase the wear resistance of joint surfaces. However, very few studies have reported on the incidence of particle-induced osteolysis for these novel materials. The aim of this study was to use a particle-induced osteolysis animal model to compare the in vivo biological response to different polymer particles. Three commercially available polymers (UHMWPE, HXLPE, and VE-HXLPE) were compared. Osseous properties including the bone volume relative to the tissue volume (BV/TV), trabecular thickness (Tb. Th), and bone mineral density (BMD) were examined using micro computed tomography. Histological analysis was used to observe tissue inflammation in each group. This study demonstrated that the osseous properties and noticeable inflammatory reactions were obviously decreased in the HXLPE group. When compared with the sham group, a decrease of 12.7% was found in BV/TV, 9.6% in BMD and 8.3% in Tb.Th for the HXLPE group. The heightened inflammatory response in the HXLPE group could be due to its smaller size and greater amount of implanted particles. Vitamin E diffused in vivo may not affect the inflammatory and osteolytic responses in this model. The morphological size and total cumulative amount of implanted particles could be critical factors in determining the biological response.

Components from 73 failed knee replacements (TKRs) consisting of rotating-platform, mobile-bearing and fixed-bearing implants were examined to assess the patterns of wear. The patterns were divided into low-grade (burnishing, abrasion and cold flow) and high-grade (scratching, pitting/metal embedding and delamination) to assess the severity of the wear of polyethylene. The rotating-platform group had a higher incidence of low-grade wear on the upper surface compared with the fixed-bearing group. By contrast, high-grade wear comprising scratching, pitting and third-body embedding was seen on the lower surface. Linear regression analysis showed a significant correlation of the wear scores between the upper and lower surfaces of the tibial insert (R(2) = 0.29, p = 0.04) for the rotating-platform group, but no significant correlation was found for the fixed-bearing counterpart. This suggests that high-grade wear patterns on the upper surface are reduced with the rotating-platform design. However, the incidence of burnishing, pitting/third-body embedding and scratching wear patterns on the lower surface was higher compared with that in the fixed-bearing knee.