In this work, we advance printed active composites by combining 3D printing, printed electronics, and liquid crystal elastomers (LCEs) to achieve soft actuators with free-standing two-way shape changing behaviors. Incorporated LCE strips are activated by Joule heating produced by printed conductive wires, while uniaxial deformation of the LCE strip is utilized as a driving force to achieve bending in the printed composite. The bending behavior of laminated hinges is first characterized in order to obtain a precise control of actuation, which is then exploited to actuate four demonstrative designs: a morphing airplane, a miura-ori structure, a cubic box, and a soft crawler. The soft morphing airplane and miura-ori structure are designed and fabricated with multiple laminated hinges to demonstrate the synergistic actions during actuation. The cubic box is constructed to show the capability of sequential folding by implementing multiple groups of conductive wires to achieve accurately addressable heating with temporal control. Finally, the two-way transformation is utilized as a driving force for the locomotion of a soft crawler stimulated by a periodic rectangular wave current. These examples show the great potential of using the hybrid 3D printing and pick-and-place method and using LCEs to achieve controllable shape change structures for a variety of potential practical applications.

A copy can be downloaded for personal non-commercial research or study, without prior permission or charge Content must not be changed in any way or reproduced in any format or medium without the formal permission of the copyright holder(s) SUMMARYFinite strain analyses of the left ventricle provide important information on heart function and have the potential to provide insights into the biomechanics of myocardial contractility in health and disease. Systolic dysfunction is the most common cause of heart failure; however, abnormalities of diastolic function also contribute to heart failure, and are associated with conditions including left ventricular hypertrophy and diabetes. The clinical significance of diastolic abnormalities is less well understood than systolic dysfunction, and specific treatments are presently lacking. To obtain qualitative and quantitative information on heart function in diastole, we develop a three-dimensional computational model of the human left ventricle that is derived from noninvasive imaging data. This anatomically realistic model has a rule-based fibre structure and a structure-based constitutive model. We investigate the sensitivity of this comprehensive model to small changes in the constitutive parameters and to changes in the fibre distribution. We make extensive comparisons between this model and similar models that employ different constitutive models, and we demonstrate qualitative and quantitative differences in stress and strain distributions for the different constitutive models. We also provide an initial validation of our model through comparisons to experimental data on stress and strain distributions in the left ventricle.

Understanding the grain size-dependent failure behavior of polycrystalline graphene is important for its applications both structurally and functionally. Here we perform molecular dynamics simulations to study the failure behavior of polycrystalline graphene by varying both grain size and distribution. We show that polycrystalline graphene fails in a brittle mode and grain boundary junctions serve as the crack nucleation sites. We also show that its breaking strength and average grain size follow an inverse pseudo Hall-Petch relation, in agreement with experimental measurements. Further, we find that this inverse pseudo Hall-Petch relation can be naturally rationalized by the weakest-link model, which describes the failure behavior of brittle materials. Our present work reveals insights into controlling the mechanical properties of polycrystalline graphene and provides guidelines for the applications of polycrystalline graphene in flexible electronics and nano-electronic-mechanical devices.

Despite the utmost importance and decades of experimental studies on fatigue in metallic glasses (MGs), there has been so far little or no atomic-level understanding of the mechanisms involved. Here we perform molecular dynamics simulations of tension-compression fatigue in Cu50Zr50 MGs under strain-controlled cyclic loading. It is shown that the shear band (SB) initiation under cyclic loading is distinctly different from that under monotonic loading. Under cyclic loading, SB initiation takes place when aggregates of shear transformation zones (STZs) accumulating at the MG surface reach a critical size comparable to the SB width, and the accumulation of STZs follows a power law with rate depending on the applied strain. It is further shown that almost the entire fatigue life of nanoscale MGs under low cycle fatigue is spent in the SB-initiation stage, similar to that of crystalline materials. Furthermore, a qualitative investigation of the effect of cycling frequency on the fatigue behavior of MGs suggests that higher cycling frequency leads to more cycles to failure. The present study sheds light on the fundamental fatigue mechanisms of MGs that could be useful in developing strategies for their engineering applications.

In this work, we introduce a modified Holzapfel-Ogden hyperelastic constitutive model for ventricular myocardium that accounts for residual stresses, and we investigate the effects of residual stresses in diastole using a magnetic resonance imaging–derived model of the human left ventricle (LV). We adopt an invariant-based constitutive modelling approach and treat the left ventricular myocardium as a non-homogeneous, fibre-reinforced, incompressible material. Because in vivo images provide the configuration of the LV in a loaded state even in diastole, an inverse analysis is used to determine the corresponding unloaded reference configuration. The residual stress in this unloaded state is estimated by two different methods. One is based on three-dimensional strain measurements in a local region of the canine LV, and the other uses the opening angle method for a cylindrical tube. We find that including residual stress in the model changes the stress distributions across the myocardium and that whereas both methods yield qualitatively similar changes, there are quantitative differences between the two approaches. Although the effects of residual stresses are relatively small in diastole, the model can be extended to explore the full impact of residual stress on LV mechanical behaviour for the whole cardiac cycle as more experimental data become available. In addition, although not considered here, residual stresses may also play a larger role in models that account for tissue growth and remodelling.