The present study aimed to formulate orodispersible tablets of flutamide (FTM) to increase its bioavailability. Orodispersible tablets were prepared by direct compression technique using three different approaches namely; super-disintegration, effervescence and sublimation. Different combined approaches were proposed and evaluated to optimize tablet characteristics. Sodium starch glycolate (SSG) was used as the superdisintegrant. The prepared powder mixtures were subjected to both pre and post compression evaluation parameters including; IR spectroscopy, micromeritics properties, tablet hardness, friability, wetting time, disintegration time and in-vitro drug release. IR studies indicated that there was no interaction between the drug and the excipients used except Ludipress. The results of micromeritics studies revealed that all formulations were of acceptable to good flowability. Tablet hardness and friability indicated good mechanical strength. Wetting and dispersion times decreased from 46 to 38 s by increasing the SSG concentration from 3.33 to 6.66% w/w in tablets prepared by superdisintegration method. The F8 formulation which was prepared by combined approaches of effervescence and superdisintegrant addition gave promising results for tablet disintegration and wetting times but failed to give faster dissolution rate. The incorporation of 1:5 solid dispersion of FTM: PEG 6000 instead of the pure drug in the same formulation increased the drug release rate from 73.12 to 96.99% after 15 min. This increase in the dissolution rate may be due to the amorphization of the drug during the solid dispersion preparation. The presence of the amorphous form of the drug was shown in the IR spectra.
In an attempt to reach better treatment of skin infections, gel formulations containing Cefotaxime (CTX) were prepared. The gel was formulated using Carbopol 934 (C934), Hydroxypropyl Methylcellulose 4000 (HPMC 4000), Carboxymethylcellulose Sodium (Na CMC), Pectin (PEC), Xanthan Gum (XG), or Guar Gum (GG). Thirteen different formulas were prepared and characterized physically in terms of color, syneresis, spreadability, pH, drug content, and rheological properties. Drug-excipients compatibility studies were confirmed by FTIR and then in vitro drug release study was conducted. In vitro and in vivo antibacterial activities of CTX were studied against wound pathogens such as, Staphylococcus aureus (S. aureus), Escherichia coli (E. coli), and Pseudomonas aeruginosa (P. aeruginosa), using either pure drug or Fucidin® cream as control. F13 provides better spreadability compared to F1 (XG) or F11 (HPMC). Moreover, the release of the drug from hydrogel F13 containing C934 was slower and sustained for 8 h. Stability study revealed that, upon storage, there were no significant changes in pH, drug content, and viscosity of the gels. Also, F13 showed the larger inhibition zone and highest antibacterial activity among other formulations. Histological analysis demonstrated that after single treatment with F13 gel formulation, a noticeable reduction in microbial bioburden occurred in case of both Gram positive and Gram negative bacterial isolates.
The synthesis and molecular characterization of new isatin-based hydrazonoindolin-2-ones 4a-o and 7a-e are reported. The in vitro anti-proliferative potential of the synthesized compounds 4a-o and 7a-e was examined against HT-29 (colon), ZR-75 (breast) and A549 (lung) human cancer cell lines. Compounds 7b, 7d and 7e were the most active congeners against the tested human cancer cell lines with average IC50 values of 4.77, 3.39 and 2.37 μM, respectively, as compared with the reference isatin-based drug, sunitinib, which exhibited an average IC50 value of 8.11 μM. Compound 7e was selected for further pharmacological evaluation in order to gain insight into its possible mechanism of action. It increased caspase 3/7 activity by 2.4- and 1.85-fold between 4 and 8 h of treatment, respectively, at 10 μM and it caused a decrease in the percentage of cells in the G1 phase of the cell cycle with a corresponding increase in the S-phase. In addition, compound 7e increased phosphorylated tyrosine (p-Tyr) levels nearly two-fold with an apparent IC50 value of 3.8 μM. The 7e-loaded PLGA microspheres were prepared using a modified emulsion-solvent diffusion method. The average encapsulation efficiency of the 7e-loaded PLGA microspheres was 85% ± 1.3. While, the in vitro release profile of the 7e-loaded microspheres was characterized by slow and continuous release of compound 7e during 21 days and the release curve was fitted to zero order kinetics. Incorporation of 7e into PLGA microspheres improved its in vitro anti-proliferative activity toward the human cancer cell line A549 after 120 h incubation period with an IC50 value less than 0.8 μM.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.