Determination of the failure limit in a repeated-load fatigue test in the laboratory has relied entirely on the arbitrary selection of a fixed criterion. The constant strain and constant stress modes of fatigue loading have been described by a consistent definition of failure in flexural fatigue testing because of the distinctly different application of energy during the loading history. The most widely accepted definition is a decrease in initial stiffness by 50 percent. Procedures examining energy input and dissipated energy have required different schemes for each mode in an attempt to describe similar states of damage in the mixture. A proposed method is presented for examining dissipated energy to select a consistent level of material behavior that is indicative of the damage accumulation in the mixture. This procedure shows the similarity between the constant stress and constant strain modes of testing and is shown to provide the potential for unifying the now phenomenological description of fatigue with a more rational energy-based description.

The nature of the interaction process between asphalt cement and crumb rubber modifier (CRM) has not been fully understood. Two main types of mechanisms that affect the produced binder properties are reported: particle swelling and degradation (devulcanization and depolymerization). These mechanisms occur as the binder is subjected to different combinations of interaction time and temperature. Insight into the mechanisms by which the interaction between the two materials takes place through monitoring the changes in the rheological parameters of the binder is provided. The effects of the interaction process variables, time and temperature, are explained. The effect of CRM properties, including particle size and material source, is also discussed.

The existence of a fatigue endurance limit has been postulated for a considerable time. With the increasing emphasis on extended-life hot-mix asphalt pavement, or perpetual pavement, verification of the existence of this endurance limit, a strain below which none or very little fatigue damage develops, has become a substantial consideration in the design of these new multilayered full-depth pavements. Fatigue data are presented that were collected on a surface mix and a binder mixture tested for an extended period from 5 million to 48 million load repetitions at strain levels down to 70 microstrain. The fatigue results are analyzed in the traditional manner and using the dissipated energy ratio. This analysis shows that there is a difference in the data at normal strain levels recommended for fatigue testing and at the low strain levels. This difference cannot substantiate an endurance limit using traditional analysis procedures, but the dissipated energy approach clearly shows a distinct change in material behavior at low flexural strain levels, which supports the fact that at low strain levels the damage accumulated from each load cycle is disproportionately less than what is predicted from extrapolations of fatigue testing at normal strain levels. This reduced damage may be attributed to the healing process. The conclusion of this study is that laboratory testing can verify the existence of a fatigue endurance limit in the range of 90 to 70 microstrain below which the fatigue life of the mixture is significantly extended relative to normal design considerations.

No abstract

No abstract

The healing phenomenon has been noted by pavement engineers for years, but its relation to hot-mix asphalt (HMA) fatigue behavior is still far from clear. This study conducted an analysis of healing and HMA fatigue behavior by introducing a specifically designed fatigue-healing test. These results help explain the differences in fatigue behavior at normal and low strain levels. An approach using the ratio of dissipated energy change, which is based on energy concepts, is used in this study. The results show that healing does exist, and its effect on fatigue life can be indicated by an energy recovery per second of rest period. The effect of healing is more prominent at low strain levels or in very long rest periods. At low strain conditions, the dominance of healing compared with the very low external load damage, considering the energy equilibrium, can result in full damage recovery. This full recovery of energy explains the existence of a fatigue endurance limit, below which HMA materials tend to have extraordinarily long fatigue lives that, as is shown, can be related to healing. The testing conducted clearly shows why polymer modification may extend the fatigue life in the field even though laboratory testing may show minimal differences compared with the neat binder test results.

From the beginning of asphalt mixture design it was desired to understand the interaction of aggregates, asphalt, and the voids created during their compaction. In asphalt mixture design, guidance is lacking in the selection of the design aggregate structure and understanding the interaction of that aggregate structure and mixture volumetric properties. Asphalt mixture design concepts are presented that use aggregate interlock and aggregate packing to develop an aggregate blend that meets volumetric criteria and provides adequate compaction characteristics. The concepts rely on coarse aggregate for the skeleton of the mixture with the proper amount of fine aggregate to provide a properly packed aggregate structure. The objective is to use aggregate packing concepts to analyze the combined gradation and relate the packing characteristics to the mixture volumetric properties and compaction characteristics. The new concepts presented for asphalt mixture design and analysis include an examination of aggregate packing and aggregate interlock, blending aggregates by volume, a new understanding of coarse and fine aggregate, and analysis of the resulting gradation. These concepts are the result of many years of field experience and are the backbone of the Bailey method for asphalt mix design. These methods are under continued development as the improved method for asphalt mixture design, which will assist with the transition to contractor mix design.

No abstract