The cascade multilevel inverters are widely used in industrial manufacturing processes for DC-AC conversion. Therefore, the reliability and efficiency improvement, optimized control, and fault-tolerant strategies are areas of interest for researchers. The fault tolerance strategies applied to cascade multilevel inverters are classified as material redundancy and analytical redundancy. This paper presents the use of the Z-source converter as a fault reconfiguration method applied to a cascade multilevel inverter. On the one hand, the proposed approach has the characteristic of combining the use of material redundancy (modifying the output voltage by changing the Z-source operation), and on the other hand, it has the use of analytical redundancy (modifying the switching sequence of the multilevel inverter, changing from symmetrical to asymmetrical operation mode). This approach has been validated by experimental results of the system under fault-free conditions and employing the Z-source converter as the main fault reconfiguration element. The proposed fault reconfiguration strategy allows the cascaded multilevel inverter to continue to operate even in the presence of a fault by having continuous operation.
In this paper an active fault tolerant control (AFTC) has been designed and applied to a 3‐DOF helicopter mathematical model. The main contribution corresponds to an AFTC design based on eigenstructure assignment aiming at reconfiguring the controller gain after actuator fault occurrences, modelled as additive faults. The reconfigured controller gain is computed ensuring the best approximation acquired for the nominal fault‐free closed‐loop system on its eigenstructure, giving rise to a faulty closed‐loop system with the same closed‐loop eigenvalues. Simulation results on the on‐line controller gain reconfiguration are shown considering simultaneous time‐varying faults and those with negative and positive slopes.
This paper focuses on the main reasons of low efficiency in a current-fed DC-DC resonant converter applied to photovoltaic (PV) isolated systems, comparing the effects derived by the overlapping time in the gate-signals (gate-source voltage) combining silicon (Si), silicon carbide (SiC), and gallium nitride (GaN)-based power devices. The results show that unidirectional switches (metal–oxide–semiconductor field-effect transistors (MOSFETs) plus diode) present hard switching as a result of the diode preventing the MOSFET capacitance of being discharged. The effectiveness of the converter was verified with a 200-W prototype with an input voltage range of 0–30.3 V, an output voltage of 200 V, and a switching frequency of 200 kHz. The reduction losses by applying GaN versus Si and SiC technologies are 66.49% and 53.57%, respectively. Alternatively, by applying SiC versus Si devices the reduction loss is 27.84%. Finally, according to the results, 60% of losses were caused by the diodes on both switches.
This paper presents a theoretical analysis of a DC-DC flyback converter variant applied in energy harvesting based on thermoelectric generators. The main contribution of the article is the analysis and obtaining the equations of the behavior of the converter with a rearrangement of the elements of the traditional flyback converter in such a way that the converter only processes part of the energy while the other part is delivered directly to the load. This is achieved by connecting the secondary of the flyback in series with the load, and this assembly, in turn, is placed in parallel with the primary and the voltage source. This configuration means that the topology can only be a boost topology; however, there are benefits such as partial power processing (R2P2) and reduced stress on converter components in both voltage and current; all this leads to increase the efficiency. A Low Frequency Averaging Analysis (LFAA) was used to determine the behavior of the proposed circuit, and a simple equivalent circuit to analyze was obtained. In order to validate the theoretical analysis, a circuit was simulated in Spice and implemented in an 18 W prototype. Experimental results showed that the converter has an efficiency of 92.65%. Moreover, the rearranged flyback processed only 56% of the input power.
The main contribution of this paper is to show a new AC/DC converter based on the rearrangement of the flyback converter. The proposed circuit only manages part of the energy and the rest is delivered directly from the source to the load. Therefore, with the new topology, the efficiency is increased, and the stress of the components is reduced. The rearrangement consist of the secondary of the flyback is placed in parallel with the load, and this arrangement is connected in series with the primary side and the rectified voltage source. The re-arranged flyback is only a reductive topology and with no magnetic isolation. It was studied as a power supply for LEDs. A low frequency averaged analysis (LFAA) was used to determine the behavior of the proposed circuit and an equivalent circuit much easier to analyze was obtained. To validate the theoretical analysis, a design methodology was developed for the re-arranged flyback converter. The designed circuit was implemented in a 10 W prototype. Experimental results showed that the converter has a THDi = 21.7% and a PF = 0.9686.
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
hi@scite.ai
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.