No abstract

The CO(2) adsorption characteristics of prototypical poly(ethyleneimine)/silica composite adsorbents can be drastically enhanced by altering the acid/base properties of the oxide support via incorporation of Zr into the silica support. Introduction of an optimal amount of Zr resulted in a significant improvement in the CO(2) capacity and amine efficiency under dilute (simulated flue gas) and ultradilute (simulated ambient air) conditions. Adsorption experiments combined with detailed characterization by thermogravimetric analysis, temperature-programmed desorption, and in situ FT-IR spectroscopy clearly demonstrate a stabilizing effect of amphoteric Zr sites that enhances the adsorbent capacity, regenerability, and stability over continued recycling. It is suggested that the important role of the surface properties of the oxide support in these polymer/oxide composite adsorbents has been largely overlooked and that the properties may be even further enhanced in the future by tuning the acid/base properties of the support.

Coal-fired power plant flue gas exhaust typically contains 3À10% oxygen. While it is known that the monoethanolamine (MEA) oxidative degradation rate is a critical parameter affecting liquid amine absorption processes, the effect of oxygen on the stability of solid amine adsorbents remains unexplored. Here, oxidative degradation of aminosilica materials is studied under accelerated oxidizing conditions to assess the stability of different supported amine structures to oxidizing conditions. Adsorbents constructed using four different silane coupling agents are evaluated, three with a single primary, secondary, or tertiary amine at the end of a propyl surface linker, with the fourth having one secondary propylamine separated from a primary amine by an ethyl linker. Under the experimental conditions used in this study, it was found that both amine type and proximity had a significant effect on oxidative degradation rates. In particular, the supported primary and tertiary amines proved to be stable to the oxidizing conditions used, whereas the secondary amines degraded at elevated treatment temperatures. Because secondary amines are important components of many supported amine adsorbents, it is suggested that the oxidative stability of such species needs to be carefully considered in assessments of postcombustion CO 2 capture processes based on supported amines.

Three classes of amine-functionalized mesocellular foam (MCF) materials are prepared and evaluated as CO(2) adsorbents. The stability of the adsorbents under steam/air and steam/nitrogen conditions is investigated using a Parr autoclave reactor to simulate, in an accelerated manner, the exposure that such adsorbents will see under steam stripping regeneration conditions at various temperatures. The CO(2) capacity and organic content of all adsorbents decrease after steam treatment under both steam/air and steam/nitrogen conditions, primarily due to structural collapse of the MCF framework, but with additional contributions likely associated with amine degradation during treatment under harsh conditions. Treatment with steam/air is found to have stronger effect on the CO(2) capacity of the adsorbents compared to steam/nitrogen.

The measurement of isosteric heats of adsorption of silica supported amine materials in the low pressure range (0-0.1 bar) is critical for understanding the interactions between CO2 and amine sites at low coverage and hence to the development of efficient amine adsorbents for CO2 capture from flue gas and ambient air. Heats of adsorption for an array of silica-supported amine materials are experimentally measured at low coverage using a Calvet calorimeter equipped with a customized dosing manifold. In a series of 3-aminopropyl-functionalized silica materials, higher amine densities resulted in higher isosteric heats of adsorption, clearly showing that the density/proximity of amine sites can influence the amine efficiency of adsorbents. In a series of materials with fixed amine loading but different amine types, strongly basic primary and secondary amine materials are shown to have essentially identical heats of adsorption near 90 kJ/mol. However, the adsorption uptakes vary substantially as a function of CO2 partial pressure for different primary and secondary amines, demonstrating that entropic contributions to adsorption may play a key role in adsorption at secondary amine sites, making adsorption at these sites less efficient at the low coverages that are important to the direct capture of CO2 from ambient air. Thus, while primary amines are confirmed to be the most effective amine types for CO2 capture from ambient air, this is not due to enhanced enthalpic contributions associated with primary amines over secondary amines, but may be due to unfavorable entropic factors associated with organization of the second alkyl chain on the secondary amine during CO2 adsorption. Given this hypothesis, favorable entropic factors may be the main reason primary amine based adsorbents are more effective under air capture conditions.