Objectives: A series of constant anatomical structures were used as guide targets for screw placement to improve the accuracy of cortical screw placement and reduce surgical injury and fluoroscopy radiation. The most commonly used angles and distances between the cortical bone screw insertion point and the lateral margins of the isthmus were selected as the contents of the questionnaire. Methods: A total of 40 physicians were selected to determine the specific values for each angle and distance. Screw placements were performed on four dry and six wet lumbar spine specimens according to the proposed anatomical target guidance technique. A total of 100 cortical bone trajectories were evaluated using X-ray and CT scanning of the specimens to verify the practicability, accuracy, and safety of the anatomical target guidance technique in screw placement. Results: The average deviation rates for angle and distance determination were 105.5% and 14.33%, respectively, indicating a significant difference between the estimated and actual values from other angles (P < 0.05). Based on visual inspection, probe penetration, X-ray, and CT examination of 100 cortical bone trajectories, the excellent rate of 40 trajectories on four dry specimens was 95%, while that of 60 trajectories on six wet specimens was 88.7%. Conclusion: Use of lumbar constant anatomical structures as targeting guidance could assist cortical bone screw placement and reduce surgical damage.

BackgroundHybrid fixation techniques including the both modified cortical bone trajectory (MCBT) and traditional trajectory (TT) at the L4 and L5 lumbar segment are firstly proposed by our team. Therefore, the purpose of this study is to evaluate and provide specific biomechanical data of the hybrid fixation techniques including the MCBT and TT.MethodsFour human cadaveric specimens were from the anatomy laboratory of Xinjiang Medical University. Four finite-element (FE) models of the L4–L5 lumbar spine were generated. For each of them, four implanted models with the following fixations were established: TT-TT (TT screw at the cranial and caudal level), MCBT-MCBT (MCBT screw at the cranial and caudal level), hybrid MCBT-TT (MCBT screw at the cranial level and TT screw at the caudal level), and TT-MCBT (TT screw at the cranial level and MCBT screw at the caudal level). A 400-N compressive load with 7.5 N/m moments was applied to simulate flexion, extension, lateral bending, and rotation, respectively. The range of motion (ROM) of the L4–L5 segment and the posterior fixation, the von Mises stress of the intervertebral disc, and the posterior fixation were compared.ResultsCompared to the TT-TT group, the MCBT-TT showed a significant lower ROM of the L4–L5 segment (p ≤ 0.009), lower ROM of the posterior fixation (p &lt; 0.001), lower intervertebral disc stress (p &lt; 0.001), and lower posterior fixation stress (p ≤ 0.041). TT-MCBT groups showed a significant lower ROM of the L4–L5 segment (p ≤ 0.012), lower ROM of the posterior fixation (p &lt; 0.001), lower intervertebral disc stress (p &lt; 0.001), and lower posterior fixation stress (p ≤ 0.038).ConclusionsThe biomechanical properties of the hybrid MCBT-TT and TT-MCBT techniques at the L4–L5 segment are superior to that of stability MCBT-MCBT and TT-TT techniques, and feasibility needs further cadaveric study to verify.

There is no detailed biomechanical research about the hybrid CBT-TT (CBT screws at cranial level and TT screws at caudal level) and TT-CBT (TT screws at cranial level and CBT screws at caudal level) techniques with finite element (FE) method. Therefore, the purpose of this study was to evaluate and provide specific biomechanical data of the hybrid lumbar posterior fixation system and compare with traditional pedicle screw and cortical screw trajectories without fusion, in FE method. Specimens were from the anatomy laboratory of Xinjiang Medical University. Four FE models of the L4-L5 lumbar spine segment were generated. For each of these, four implanted models with the following instruments were created: bilateral traditional trajectory screw fixation (TT-TT), bilateral cortical bone trajectory screw fixation (CBT-CBT), hybrid CBT-TT fixation, and hybrid TT-CBT fixation. A 400 N compressive load with 7.5 Nm moments was applied so as to simulate flexion, extension, left lateral bending, right lateral bending, left rotation, and right rotation, respectively. The range of motion (ROM) of the L4-L5 segment and the posterior fixation, the von Mises stress of the intervertebral disc, and the posterior fixation in four implanted models were compared. CBT-TT displayed a lower ROM of the fixation segment (3.82 ± 0.633°) compared to TT-TT (4.78 ± 0.306°) and CBT-CBT (4.23 ± 0.396°). In addition, CBT-TT showed a lower ROM of the posterior fixation (0.595 ± 0.108°) compared to TT-TT (0.795 ± 0.103°) and CBT-CBT (0.758 ± 0.052°). The intervertebral disc stress of CBT-TT (4.435 ± 0.604 MPa) was lower than TT-TT (7.592 ± 0.387 MPa) and CBT-CBT (6.605 ± 0.600 MPa). CBT-TT (20.228 ± 3.044 MPa) and TT-CBT (12.548 ± 2.914 MPa) displayed a lower peak von Mises stress of the posterior fixation compared to TT-TT (25.480 ± 3.737 MPa). The hybrid CBT-TT and TT-CBT techniques offered superior fixation strength compared to the CBT-CBT and TT-TT techniques.

Debridement from single posterior approach is an effective technique for the internal fixation of lumbosacral regional spinal tuberculosis. An appropriate selection of indications, careful evaluation of radiology, and thorough debridement were the key to a successful operation.

No abstract